Panasonic Appliance Error Codes

E01

Door unlocked - The door is not locked properly.

Washing Machine

E02

Water filling issue - The water inlet valve may be faulty.

Washing Machine

E03

Pump failure - The pump may not be working correctly.

Washing Machine

E04

Overflow error - There may be a leak in the machine.

Washing Machine

E05

NTC or heater error - There may be a problem with the NTC or the heater.

Washing Machine

E06

Motor failure - There may be an open circuit, short circuit or disconnected motor issue.

Washing Machine

E08

Motor triac short circuit - There may be an issue with the motor triac.

Washing Machine

E08

Motor triac short circuit - An issue with the motor triac has been detected.

Washing Machine

H01

Water level sensor error - There's a problem with the water level sensor.

Washing Machine

H02

Motor triac error - There's a problem with the motor triac.

Washing Machine

H04

Load relay short circuit error - There's a problem with the load relay circuit.

Washing Machine

H05

Memory circuit of IC issue - There's a problem with the memory circuit of the IC.

Washing Machine

H12

Safety switch connection error - There's a problem with the safety switch connection.

Washing Machine

H17

Thermistor error (for X series) - The thermistor sensor in the X series has detected an irregular signal or is out of range.

Washing Machine

H18

Motor thermistor sensor detected irregular signal or out of range - Check motor connections.

Washing Machine

H21

Overflow error - There is an issue with water overflowing in the washing machine.

Washing Machine

H23

Heater relay on main control PCB detected abnormal or out of range - There is probably an issue with the electronic controller.

Washing Machine

H25

Motor error - There is a possible main motor wiring problem.

Washing Machine

H27

The washing machine door lock cannot engage with the latch in place - The door lock cannot lock with the latch in its current position.

Washing Machine

U12

The door is not shut properly, close it securely and press start button

Dryer

U15

The water container is full, empty it and set the water drain hose properly, turn the power on and press start button

Dryer

U30

Operate the appliance within the operating temperature range of 5 ºC - 35 ºC

Dryer

H*

Inspection is required, pull out the power plug and contact customer service with the displayed content (2-digit number after H)

Dryer

H99

Error in inverter's on/off control

Oven

H98

Magnetron has no oscillation

Oven

H97

Error in inverter input

Oven

H96

Error in custom IC inverter

Oven

H95

Failure in inverter input

Oven

H90

Inverter thermistor controls power down

Oven

H44

Failure in keyboard switch

Oven

H39

Failure in steam heater thermistor

Oven

H32

Failure in magnetron thermistor

Oven

H30

Failure in oven thermistor

Oven

H02

Memory IC error, may appear in test or cooking mode.

Oven

H00

RAM failure, may appear in test or cooking mode.

Oven

H20

Steam heater open error.

Oven

U14

No water during steam cooking, may appear in test or cooking mode.

Oven

U40

No load operation.

Oven

U65

Thermistor-controlled power down by magnetron.

Oven

HOT

Oven is hot, may appear in test or cooking mode.

Oven

F33

Open temperature sensor (exhaust).

Oven

F34

Short temperature sensor (exhaust), rare.

Oven

F44

Shorted membrane switch.

Oven

F01

Exhaust temperature exceeds 120°C (260°F); food is overcooked.

Oven

F05

Failure in digital programmer circuit.

Oven

F09

Oven designed for 50Hz is operated in a 60Hz environment; controller board failure.

Oven

F81

Excessive current consumption in upper H.V. circuit.

Oven

F82

Excessive current consumption in lower H.V. circuit.

Oven

F86

Relay failure in RY-3; shorted contacts; digital programmer circuit failure.

Oven

F87

Shorted contacts in RY-4.

Oven

H02

Memory IC error (can occur in both test and cooking modes).

Microwave

H00

RAM failure (can occur in both test and cooking modes).

Microwave

H20

Steam heater open error.

Microwave

U14

No water during steam cooking (can occur in both test and cooking modes).

Microwave

U40

No load operation.

Microwave

U65

Power down controlled by magnetron thermistor.

Microwave

H99

Inverter on/off control error.

Microwave

H98

Magnetron no oscillation error.

Microwave

H97

Inverter input error.

Microwave

H96

Inverter custom IC error.

Microwave

H95

Inverter input failure.

Microwave

H90

Power down controlled by Inverter thermistor.

Microwave

H44

Keyboard switch failure.

Microwave

H39

Steam heater thermistor failure.

Microwave

H32

Magnetron thermistor failure.

Microwave

H12

Inappropriate device capacities

Heat pump

H15

Fault with compressor temperature sensor

Heat pump

H20

Fault with circulation pump

Heat pump

H23

Fault with coolant sensor

Heat pump

H27

Fault with service valve

Heat pump

H28

Fault with solar sensor

Heat pump

H31

Fault with swimming pool sensor

Heat pump

H36

Fault with buffer tank sensor

Heat pump

H38

Fault due to non-matching device brands

Heat pump

H62

Fault with upstream with the flow monitor.

H63

Fault with the low pressure sensor.

H64

Fault with the high pressure sensor.

H65

Fault with the water circulation during defrosting.

H67

Fault with outdoor temperature sensor 1.

H68

Fault with outdoor temperature sensor 2.

H70

Fault with overload protection for indoor units E-heating element.

H72

Fault with hot water tank temperature sensor.

H74

Fault with the PCB communication.

H75

Low water temperature protection.

H76

Fault with the PCB communication.

H90

Communication fault.

H91

Fault with overload protection for hot water E-heating.

Heat pump

H95

Fault with incorrect voltage IU - OU.

Heat pump

H98

Fault due to high pressure protection.

Heat pump

H99

Fault due to frost protection of indoor units heat exchanger.

Heat pump

F12

High pressure switch in the outdoor unit triggered.

Heat pump

F14

Incorrect compressor speed.

Heat pump

F15

Incorrect speed of the OU fan motor.

Heat pump

F16

Fault due to excessive current consumption.

Heat pump

F20

Fault due to overload protection of the compressor.

Heat pump

F20

Fault due to overload protection of the compressor.

Heat pump

F22

Fault due to overload protection of power transistor.

Heat pump

F23

Fault due to direct current peaks in the outdoor unit.

Heat pump

F24

Fault due to problems in the cooling circuit.

Heat pump

F25

Fault due to problems with the switching interval.

Heat pump

F27

Fault with the high pressure switch in the outdoor unit.

Heat pump

F29

Low hot gas superheat.

Heat pump

F30

Fault with the inflow temperature sensor.

Heat pump

F32

Fault with the room thermostat.

Heat pump

F36

Fault with the outdoor temperature sensor.

Heat Pump

F37

Fault with the return flow temperature sensor.

Heat Pump

F40

Fault with the hot gas temperature sensor in the outdoor unit.

Heat Pump

F41

Error in the power factor correction.

Heat Pump

F42

Error with the heat exchanger sensor in the outdoor unit.

Heat Pump

F43

Fault with hot gas temperature sensor in the outdoor unit.

Heat Pump

F43

Fault with hot gas temperature sensor in the outdoor unit.

Microwave

F45

Fault with the defrost temperature sensor in the outdoor unit.

Microwave

F46

Current transformer switching off.

Microwave

F48

Error with evaporator outlet temperature sensor.

Microwave

F49

Fault with bypass outlet temperature sensor in the OU.

Microwave

F95

Fault due to HP protection cooling in the outdoor unit.

Microwave

E1

Long water inlet time

Coffee Machine

E3

Heating Abnormal

Coffee Machine

E4

Water overflow

Coffee Machine

E6

Failure of Varistor

Coffee Machine

E7

Failure of Varistor

Coffee Machine

E8

Failure of Orientation of Distributary Valve

Coffee Machine

E1

Water filling exceeded pre-set time

Dishwasher

E3

Heating exceeded pre-set time

Dishwasher

E4

Overflow

Dishwasher

E6

Open-circuit failure of thermistor

Dishwasher

E7

Short-circuit failure of thermistor

Dishwasher

Sr

Failure/Warning

LF

Freezer compartment is not cold enough.

LC

Refrigerator compartment is not cold enough.

LF and LC

Not cold enough.

HC

Refrigerator compartment is too cold.

LOPO

Low voltage.