Household Appliance Error Codes

E3

This error code indicates a door lock error in the washing machine. The door of the washing machine did not close properly or the door lock is faulty.

Washing Machine

F01

This error code indicates that the washing machine isn’t filling with water.

Washing Machine

F02

This error code indicates a heating component timeout in the washing machine. The water isn’t heating up because there’s a problem with the washing machine’s heating element.

Washing Machine

F03

This error code indicates that the washing machine is taking too long to drain.

Washing Machine

F04

This error code indicates a motor fault in the washing machine, as indicated by no tacho signal.

Washing Machine

F05

This error code indicates that the washer experienced uncontrolled motor startup or high resistance connections.

Washing Machine

F06

This error code indicates that there’s an NTC short circuit in the washing machine.

Washing Machine

F07

This error code indicates a faulty NTC circuit has been detected in the washing machine.

Washing Machine

F08

This error code indicates that the door was open when the program attempted to start in the washing machine.

Washing Machine

F09

This error code indicates that the washing machine is heating up unexpectedly.

Washing Machine

F10

This error code indicates a communication error in the washing machine.

Washing Machine

F11

This error code indicates that the heat sink or motor control PCB in the washing machine has overheated.

Washing Machine

F12

This error code indicates a short circuit or a faulty motor in the washing machine.

Washing Machine

F13

This error code indicates that the mains voltage entering the washing machine is too high.

Washing Machine

F14

This error code indicates that the mains voltage entering the washing machine is too low.

Washing Machine

F15

This error code indicates a faulty temperature sensor on the motor PCB in the washing machine.

Washing Machine

F16

This error code indicates a door open issue in the washing machine.

Washing Machine

E16

This error code indicates a door open issue in the washing machine.

Washing Machine

E17

This error code indicates an inlet valve issue in the washing machine.

Washing Machine

F18

This error code indicates a pump or drain time-out issue in the washing machine because the drain hose is blocked.

Washing Machine

E18

This error code indicates a pump or drain time-out issue in the washing machine because the drain hose is blocked.

Washing Machine

F19

This error code indicates that the heating time has been exceeded in the washing machine.

Washing Machine

E19

This error code indicates that the heating time has been exceeded in the washing machine.

Washing Machine

F20

This error code indicates a heating fault detected in the washing machine.

Washing Machine

E23

This error code indicates that water was detected in the base trough because the appliance is leaking.

Washing Machine

F23

This error code indicates that water was detected in the base trough because the appliance is leaking.

Washing Machine

E27

This error code indicates a malfunction of the pressure system in the washing machine.

Washing Machine

F28

This error code indicates a flow sensor issue in the washing machine.

Washing Machine

E28

This error code indicates a flow sensor issue in the washing machine.

Washing Machine

F42

This error code indicates a motor fault indicated in the washing machine.

Washing Machine

F44

This error code indicates a motor fault indicated in the washing machine.

Washing Machine

E56

This error code indicates an unexpected communication error in the washing machine.

Washing Machine

E:17

Lint screen temperature sensor error

Dryer

E:18

Heater temperature sensor error

Dryer

E:20

Defective control module in the dryer

Dryer

E:21

Control module issue in the dryer

Dryer

E:22

Defective control module detected in the dryer

Dryer

E:23

Control module problem in the dryer

Dryer

E:24

Control module issue detected in the dryer

Dryer

E:25

Defective control module identified in the dryer

Dryer

E:26

Control module defect in the dryer

Dryer

E:01

Temperature increase caused by obstructed air outlet

Dryer

E:11

Temperature increase due to blocked air duct

Dryer

E:12

Heat buildup from clogged air path

Dryer

E:17

Lint screen temperature sensor error

Dryer

E:18

Heater temperature sensor error

Dryer

E:03

The drying cycle has surpassed its maximum duration

Dryer

E:13

The drying cycle has surpassed its maximum duration

Dryer

F31

Oven temperature sensor failure. Check sensor probe for dirt buildup, repair connection at sensor plug, or control malfunction.

Oven

F33

Drawer sensor failure. Non-critical error. Ignore if not using the drawer frequently.

Oven

F41

Faulty latch motor or wiring. Check latch switches and wires attached to appliance chassis.

Oven

F43

Motorized latch will not unlock. Lubricate the lock, check hinges and door gasket, replace lock if persists.

Oven

F45

Faulty or jammed upper oven door.

Oven

ER1

Temperature sensor failure. Check temperature sensor wiring, sensor, and control module.

Oven

ER2

Problems with connection to electrical network. Check main supply connection, terminal connection block, and control module.

Oven

ER3

Oven overheating. Switch off the device and let it cool for some time.

Oven

ER6

Defective door lock. Check the door lock and get it replaced if faulty.

Oven

ER8

Circuit problems. Seek help from an expert appliance repair serviceman.

Oven

E005

Protective relay won't turn on. Turn the device on and off.

Oven

E011

Malfunction due to water or dirt entering the control panel. Clean the control panel or call appliance repair experts.

Oven

E115

Temperature too high. Turn off the device and let it cool down.

Oven

ER1

The temperature sensor has failed.

Stove

ER2

The mains connection is faulty.

Stove

ER4

The temperature sensor has failed.

Stove

ER6

The door lock is faulty.

Stove

ER7

The door release mechanism is faulty.

Stove

F32

The temperature sensor has failed.

Stove

F41

The latch motor or its wiring is faulty.

Stove

F42

The lower oven door is faulty or jammed, or the latch switches are not functioning properly.

Stove

F43

The latch motor or its wiring is faulty.

Stove

F44

The latch motor or its wiring is faulty.

Stove

F45

The upper oven door is defective or jammed, or the latch switches are not functioning properly.

Stove

H95

The microwave door is not completely closed.

Microwave

E723

The microwave door is not securely closed.

Microwave

Er1

The microwave's temperature sensor is not functioning properly.

Microwave

Er11

The buttons on the microwave are either dirty or jammed.

Microwave

E12

There is a limescale buildup in the dishwasher.

Dishwasher

E14

There is a failure with the flow meter in the dishwasher.

Dishwasher

E15

Water is in the base trough of the dishwasher.

Dishwasher

E18

There is an issue with water flow into the dishwasher.

Dishwasher

E22

The filter in the dishwasher is blocked.

Dishwasher

E23

There is an issue with the drain pump in the dishwasher.

Dishwasher

E24

The dishwasher is not draining properly.

Dishwasher

E25

The drain pump is blocked, there is a drain issue, the filter is clogged or the pump impeller is jammed.

Dishwasher

E16

Water is filling up the dishwasher system.

Dishwasher

E17

The dishwasher is unable to stop filling with water.

Dishwasher

E01

There is a fault with the temperature sensor in the refrigerator compartment.

Fridge

E02

There is a fault with the temperature sensor in the freezer compartment.

Fridge

E03

There is a fault with the temperature sensor in the temperature-controlled drawer.

Fridge

E10

There is a fault with the main control board module.

Fridge

E11

There is a fault with the display control module.

Fridge

E15

There is a fault with the ambient temperature sensor.

Fridge

E20

There is a communication error between the main control board module and the display control module.

Fridge

E21

There is a communication error between the display control module and the ice and water dispenser control module.

Fridge

1E

This error code indicates a problem with the water level sensor.

Washing Machine

E7

This error code also indicates a problem with the water level sensor.

Washing Machine

3E

This error code suggests a defect in the motor.

Washing Machine

EA

This error code also suggests a defect in the motor.

Washing Machine

EB

This error code also suggests a defect in the motor.

Washing Machine

3E1

This error code indicates a motor overload, potentially caused by too much laundry in the appliance or a disconnection of the hall sensor terminal or a possible PCB fault.

Washing Machine

3E2

This error code suggests a motor driving error, possibly due to a weak or unstable relay operation. It is recommended to replace the Motor PCB.

Washing Machine

3E2

This error code indicates a problem with the motor driving in the washing machine, potentially caused by weak or unstable relay operation in the PBA board.

Washing Machine

3E3

This error code is related to a problem with the Quiet-Drive Motor in the washing machine, which may be due to a faulty motor hall sensor, PCB connection, or a misplaced Quiet Drive motor cover.

Washing Machine

3E4

This error code is related to a defect in the Quiet-Drive Motor, which may be caused by a lack of connection to the PCB Housing terminal, a fault in the PCB, or a malfunction in the Quiet-Drive Motor itself.

Washing Machine

4E

This error code indicates a water supply issue in the washing machine, which only occurs after 10 minutes if the pressure sensor does not detect the unit filling with water.

Washing Machine

4E1

This error code is related to a water temperature issue in the washing machine, and may be caused by an incorrect connection of the water hose to a hot water supply.

Washing Machine

4E2

This error code indicates a water temperature error in the washing machine, meaning that the water is too hot for the selected wash cycle.

Washing Machine

E2

This error code indicates a water drain issue in the washing machine, which occurs after 10 minutes if the machine is not draining water.

Washing Machine

5E

This error code also signals a problem with water draining from the washing machine after 10 minutes into a cycle.

Washing Machine

OE

This error code indicates an overflow issue in the washing machine, which occurs when too much water or foam has entered the appliance.

Washing Machine

E3

This error code is also related to an overflow problem in the washing machine, where too much water or foam has entered the appliance.

Washing Machine

OE

This error code is shown when there is an overflow issue, meaning too much water or foam has entered the washing machine.

Washing Machine

OF

This error code is displayed when the water has reached the overflow level in the washing machine.

Washing Machine

Sud

This error code is shown when the washing machine has detected an excessive amount of foam in the drum.

Washing Machine

Sud

This error code is typically not a fault, as the washing machine will normally resolve the issue on its own. However, if the problem persists, you can try running an "Eco drum clean" cycle or a 90°C cotton cycle with no detergent and no washing inside. If the problem still persists, check the pressure system and sump for any debris.

Washing Machine

Sud

This error code indicates that there is excessive foam detected in the washing machine.

Washing Machine

tE1

This error code indicates a problem with the water heater temperature sensor in the washing machine.

Washing Machine

tE2

This error code indicates a problem with the fan housing duct sensor in the washing machine.

Washing Machine

tE3

This error code indicates a problem with the condenser duct sensor in the washing machine.

Washing Machine

UC

This error code appears when the supply voltage fluctuates outside the range of 176-286vAC. It could indicate a problem with the power supply.

Washing Machine

UE

This error code indicates an unbalanced load in the washing machine drum. The machine may have stopped the spin cycle for safety reasons. You can redistribute the washing more evenly or check the condition of the weights, balancers, shock absorbers and springs.

Washing Machine

E4

The washing load in the drum is unbalanced. The machine may have stopped the spin cycle for safety reasons. Please distribute the laundry evenly to resolve the issue.

Washing Machine

t1

This error code indicates that the washing machine is in test mode.

Washing Machine

t2

This error code indicates that the washing machine is in test mode.

Washing Machine

tSt

This error code indicates that the washing machine is in test mode.

Washing Machine

tE

This error code indicates an issue with the temperature sensor in the washing machine.

Washing Machine

EC

This error code indicates an issue with the temperature sensor in the washing machine.

Washing Machine

9C1

Abnormal voltage being supplied to the dryer, may appear if the dryer is stacked with washer

Dryer

9E

Abnormal voltage being supplied to the dryer

Dryer

2E

Abnormal voltage being supplied to the dryer

Dryer

9E1

Abnormal voltage being supplied to the dryer

Dryer

bE

A button on the panel is detected as stuck or continuously pressed.

Dryer

bE2

A button on the panel is detected as stuck or continuously pressed.

Dryer

bC2

A button on the panel is detected as stuck or continuously pressed.

Dryer

6E

A button on the panel is detected as stuck or continuously pressed.

Dryer

6E2

A button on the panel is detected as stuck or continuously pressed.

Dryer

6C2

A button on the panel is detected as stuck or continuously pressed.

Dryer

bE

Jammed button error - a button on the panel is detected as stuck or continuously pressed.

Dryer

bE2

Jammed button error - a button on the panel is detected as stuck or continuously pressed.

Dryer

bC2

Jammed button error - a button on the panel is detected as stuck or continuously pressed.

Dryer

6E

Jammed button error - a button on the panel is detected as stuck or continuously pressed.

Dryer

6E2

Jammed button error - a button on the panel is detected as stuck or continuously pressed.

Dryer

6C2

Jammed button error - a button on the panel is detected as stuck or continuously pressed.

Dryer

AC

Communication error - internal components cannot communicate with each other.

Dryer

FC

Frequency error - Invalid power source frequency

Dryer

FE

Frequency error - Invalid power source frequency

Dryer

1 FC

Frequency error - Invalid power source frequency

Dryer

3C

Motor error

Dryer

oD

Dry time error

Dryer

1 AC7

Electronic control error

Dryer

HC2

Gas ignition error

Dryer

tS

Temperature error

Dryer

t5

Temperature error

Dryer

tC

Temperature error

Dryer

tO

Temperature error

Dryer

t0

Temperature error

Dryer

tE

Temperature error

Dryer

tE3

Temperature error

Dryer

tC5

Temperature error

Dryer

tCS

Temperature error related to the sensors that measure it

Dryer

1 tC

Temperature error with temperature sensors

Dryer

1tC5

Temperature error with temperature sensors

Dryer

1tCS

Temperature error with temperature sensors

Dryer

AC

Communication error between dryer's internal components

Dryer

Et

Communication error between dryer's internal components

Dryer

AE

Communication error between dryer's internal components

Dryer

EEE

Communication error between dryer's internal components

Dryer

AE4

Communication error between dryer's internal components

Dryer

AC

Internal components are unable to communicate with each other

Dryer

Et

Internal components are unable to communicate with each other

Dryer

AE

Internal components are unable to communicate with each other

Dryer

EEE

Internal components are unable to communicate with each other

Dryer

AE4

Internal components are unable to communicate with each other

Dryer

AE3

Internal components are unable to communicate with each other

Dryer

AE5

Internal components are unable to communicate with each other

Dryer

E3

Communication error

Dryer

1 AC

Communication error

Dryer

Clg

The vent is clogged

Dryer

Cl9

The vent is clogged

Dryer

Cg

The vent is clogged

Dryer

C9

The vent is clogged

Dryer

C80

Approximately 80% of the vent is clogged

Dryer

E08

Oven not heating properly due to issues with heating elements, broil element, baking element, or temperature sensor.

Oven

E-OA

Oven overheating due to temperature sensor issue.

Oven

E27 and E28

Temperature sensor issues.

Oven

SE

Defective key in control panel.

Oven

LE

Low voltage error.

Oven

E54

Electronic control board error.

Oven

E-55

Communication error with touch panel.

Oven

cE-56

Oven's internal electronic control board issue.

Oven

E-OE

Oven door lock error.

Oven

C0, C1, C2, C3

Sensor error

Stove

d0

Stuck button error

Stove

F0, F1, F2

Communication error

Stove

Underlined u

Pan detection error

Stove

C-10, C-11, C-12

Error with gas/easy/PH sensor

Microwave

C-20, C-21, C-22

Error with temp sensor

Microwave

C-70, C-71, C-72

Error with steam sensor

Microwave

C-A0, C-A1, C-A2

Functional error

Microwave

C-d0, C-d1, C-d2

Door or Key error

Microwave

C-F0, C-F1, C-F2

Communication error

Microwave

E-01

Open error

Microwave

E-02

Cooking time setting over error (microwave)

Microwave

E-03

Cooking time setting over error (grill)

Microwave

E-03

Cooking time setting over error (grill)

Microwave

E-04

Cooking time setting over error (convection)

Microwave

E-05

Cooking time setting over error (combination)

Microwave

E-06

Swing heater error

Microwave

E-11

Open gas sensor error

Microwave

E-12

Short gas sensor error

Microwave

E-13

T1 max time gas sensor error

Microwave

E-14

Dry up / no load gas sensor error

Microwave

E-21

Open temp sensor error

Microwave

E-22

Short temp sensor error

Microwave

E-22

Short temp sensor error

Microwave

E-23

T1 max time error

Microwave

E-24

Over temperature error

Microwave

E-25

Micro cook abnormal temperature error

Microwave

E-26

Temperature not over AD error

Microwave

E-31

Open gas sensor error

Microwave

E-32

Short gas sensor error

Microwave

E-33

Under weight error

Microwave

E-33

Under weight error

Microwave

E-34

Over weight error

Microwave

E-35

Invalid weight error

Microwave

E-36

Door open error

Microwave

E-41

Open easy/PH sensor error

Microwave

E-42

Short easy/PH sensor error

Microwave

E-43

T1 max time easy/PH sensor error

Microwave

E-44

Dry up easy/PH sensor error

Microwave

E-45

Cooling error

Microwave

E-46

Primary open error

Microwave

E-51

Sense failure

Microwave

E-52

EEPROM short error

Microwave

E-53

Read/write error

Microwave

E-54

Zero error

Microwave

E-61

Open humidity sensor error

Microwave

E-62

Short humidity sensor error

Microwave

E-63

T1 max time humidity sensor error

Microwave

E-71

Steam sensor open error

Microwave

E-71

Steam sensor open error

Microwave

E-72

Steam sensor short error

Microwave

E-81

Communication open error

Microwave

E-82

Communication short error

Microwave

E-83

Communication error

Microwave

E-X1

Additional open error

Microwave

E-X2

Additional short error

Microwave

-SE-

Key short error

Microwave

TE

Touch communication error

Microwave

E 1 or 21

Defective temperature sensor in the room

Heat pump

E 1 or 22

Defective heat exchanger temperature sensor

Heat pump

E1 or 54

Defective fan motor or capacitor

Heat pump

E1 or 63

Defective EEPROM

Heat pump

E5

Short or open indoor heat exchanger sensor

Heat pump

E6

Short or open outdoor heat exchanger sensor

Heat pump

E7

Short or open heater temperature sensor

Heat pump

3C

Pump operation error

Dishwasher

1E, IE

Clogged filter error

Dishwasher

3E

High temperature water supply error

Dishwasher

4C, 4E

Water supply error

Dishwasher

5C, 5E

Drain error

Dishwasher

7E

Water reflector error

Dishwasher

9E

Low water level error

Dishwasher

AP

Access Point Mode

Dishwasher

bE, 6E

Button error

Dishwasher

CE

Communication error

Dishwasher

HC, IE, 1E

High temperature heater error

Dishwasher

HE, tE

Heater error

Dishwasher

LC, LE

Leakage error

Dishwasher

OC, 0C, oE

Over level water error

Dishwasher

PC

Zone wash error

Dishwasher

PE

Half load connection error

Dishwasher

AP

The refrigerator is acting as an access point.

Refrigerator

Freezer Fan Error

The fan is not sensing rotational feedback.

Refrigerator

22E, 22C

The fridge fan has an error, may be caused by leaving the door open too long.

Refrigerator

41 or 42 and interior blue lights flashing

Reboot the Family Hub using the power switch on the inside at the top of the right door.

Refrigerator

41C

Latest software update must be installed, tap OK after error occurs for the first time.

Refrigerator

76C or blinking Autofill indicator

Water detected in the Autofill compartment.

Refrigerator

85C

Low voltage detected on the power source, cleared by pressing OK for 3 seconds.

Refrigerator

83E

Compressor Abnormal Current Detection Error. A power surge or other electrical anomaly may have occurred.

Fridge

85E

Compressor Under Voltage Error. A brownout condition may have occurred.

Fridge

86E

Compressor Over Voltage Error. A power surge may have occurred, such as during a thunderstorm.

Fridge

88 88

Communication Fault. This error can occur if power is disrupted during bootup.

Fridge

PC ER, PC CH

Communication Error. This is a communication error between components in the refrigerator, and can occur if there was a recent power surge or if the doors are not properly connected.

Fridge

OF OF, O FF, OFF OFF, or scrolling temperature bars

Cooling Off Mode. If the display is showing OF OF, O FF, OFF OFF, or scrolling temperature bars, the refrigerator is in Cooling Off Mode, sometimes called Demo mode or Shop mode. Service is not required.

Fridge

5E

Fridge Defrost Sensor Error.

Fridge

8E

Ice Maker (Freezer) Sensor Error.

Fridge

14E

Ice Maker Sensor Error

Refrigerator

33E

Ice Pipe Heater Error

Refrigerator

39E, 39C

Ice Maker Function Error

Refrigerator

40E, 40C

Ice Room Fan Error

Refrigerator

84C

Compressor Lock

Refrigerator

F1

This error code indicates a problem with the NTC sensor caused by an issue with the water or heating system.

Washing Machine

F2

This error code indicates a problem with the NTC sensor caused by an issue with the water or heating system.

Washing Machine

F10

This error code signifies that there is a blockage in the water intake system of the washing machine.

Washing Machine

F11

This error code indicates a drain fault in the washing machine, likely caused by a blockage in the drainage hose or clog in the drain pump.

Washing Machine

F12

This error code suggests a water intake issue at the start of a cycle, which can be caused by a closed water intake valve or lack of water supply to the machine.

Washing Machine

F13

This error code highlights a water intake issue due to a problem with the heat pressure switch, which can be caused by a faulty water intake valve.

Washing Machine

F14

This error code indicates a problem with the heater pressure switch, which may need to be replaced, and that the connections and circulation pump capacitor should also be checked for proper function.

Washing Machine

F15

The error code indicates a problem with the hot water intake, such as a clogged filter or a turned off valve.

Washing Machine

F16

This error code shows that there is excessive foam in the washing machine, which can be caused by using too much detergent or the incorrect type of detergent.

Washing Machine

F19

The error code indicates that the flow meter is stiff and not turning freely, which can be due to a faulty water intake valve that needs to be replaced.

Washing Machine

F20

This error code indicates that the water is not being heated.

Washing Machine

F24

This error code indicates a problem with the heater relay contact, which is faulty.

Washing Machine

F25

This error code indicates a problem with the desired temperature, which is faulting.

Washing Machine

F26

This error code indicates a problem with the NTC sensor, which detected temperatures above 194 degrees Fahrenheit.

Washing Machine

F29

This error code indicates that the heater steam is inactive.

Washing Machine

F34

This error code indicates that locking is not possible in the washing machine.

Washing Machine

F39

This error code indicates an electronic unit fault BAE in the washing machine.

Washing Machine

F40

This error code indicates an electronic unit fault in the washing machine.

Washing Machine

F41

This error code indicates that the wash cycle has been aborted in the washing machine.

Washing Machine

F42

This error code indicates that there is no recognition of mains frequency.

Washing Machine

F43

This error code means that the model type has not been programmed into the washing machine.

Washing Machine

F45

This error code indicates that the flash RAM is defective and is giving incorrect information.

Washing Machine

F46

This error code indicates that the LCD connection is defective and the display is not connected correctly.

Washing Machine

F47

This error code indicates that there is a defect in the BAE/SLT interface.

Washing Machine

F50

This error code indicates a drive error, where the drum is not able to move.

Washing Machine

F51

This error code indicates a problem with the pressure switch.

Washing Machine

F52

This error code indicates that the heating pressure switch reset during heating.

Washing Machine

F53

This error code indicates a speed sensor fault.

Washing Machine

F56

This error code indicates that the final spin is less than 400 RPM.

Washing Machine

F62

This error code indicates a defective program selector.

Washing Machine

F63

This error code indicates a faulty water path control unit.

Washing Machine

F65

This error code indicates a fault with the drum light assembly.

Washing Machine

F67

This error code indicates a circulation pump speed that is too low.

Washing Machine

F68

This error code indicates that the circulation pump is operating after switch-off.

Washing Machine

F69

This error code indicates that the circulation pump is blocked.

Washing Machine

F70

Faulty float switch

Washing Machine

F81

Heater unit – steam inactive.

Washing Machine

F83

Heater unit – steam – excessive temperature

Washing Machine

F84

This error code indicates a Fault with the slide shutter positioning in the washing machine.

Washing Machine

F85

This error code indicates a problem with the slide shutter signal.

Washing Machine

F86

This error code indicates a problem with salt container lid contact.

Washing Machine

F87

This error code indicates a problem with the sensor softener.

Washing Machine

F88

This error code indicates a problem with the turbidity sensor.

Washing Machine

F91

This error code indicates a problem with the washing machine's load sensor.

Washing Machine

F92

There is a bacterial contamination risk in your machine.

Washing Machine

F100

Communication link failure.

Washing Machine

F102

Communication to smart house bus failure.

Washing Machine

F103

Smart house bus link incompatibility.

Washing Machine

F104

Drive / low voltage.

Washing Machine

F138

Water in the drip tray.

Washing Machine

F140

Drainage dispenser unit fault.

Washing Machine

F220

This error code indicates a water supply fault.

Washing Machine

F1

NTC heater sensor short circuit

Dryer

F2

NTC heater sensor open circuit

Dryer

F3

NTC fan sensor short circuit

Dryer

F4

NTC fan sensor open circuit

Dryer

F32

Door lock doesn't close

Dryer

F33

Door lock doesn't open

Dryer

F36

Defective door switch

Dryer

F39

Electronic unit fault

Dryer

F41

Faulty EEPROM

Dryer

F45

Flash RAM defect

Dryer

F46

LCD connection defective

Dryer

F55

Laundry isn't dry after 180 minutes

Dryer

F66

Airpath leak

Dryer

F5

Oven PT1000 Sensor Short Circuit

Oven

F6

Oven PT1000 Sensor Open Circuit

Oven

F7

Catalyser PT1000 Sensor Open Circuit

Oven

F9

PT1000 Kat Sensor Open Circuit

Oven

F21

Faulty Grill Heating Element

Oven

F22

Faulty Oven Fan Forced Element

Oven

F23

Pyrolysis Heating Fault

Oven

F30

Different Signal Between Door & Door Contact

Oven

F31

Door Open with Defective Door Lock

Oven

F32

Door Lock Does Not Close

Oven

F33

Door Lock Does Not Open

Oven

F43

Model Type Not Programmed

Oven

F47

BAE / SLT Interface Defective

Oven

F48

BAE / O2 Sensor Interface Defective

Oven

F54

Spit Shot Circuit

Oven

F55

Over Riding Time Control Over Run

Oven

F57

Faulty Cooling Fan

Oven

F60

Faulty Hot Air Fan

Oven

F61

Excessive temperature

Oven

F89

Faulty O2 Sensor

Oven

F90

Faulty O2 System

Oven

F102

Communication to Smart House Bus Failure

Oven

F103

Smart House Bus Link Incompatibility

Oven

F180

PT1000 Sensor Short Circuit Double Oven (Lower Oven)

Oven

F181

PT1000 Sensor Open Circuit Double Oven (Lower Oven)

Oven

F182

PT1000 Catalyser Sensor Short Circuit Double Oven (Lower Oven).

Oven

F183

PT1000 Catalyser Sensor Open Circuit Double Oven (Lower Oven).

Oven

F184

Pyrolysis Heating Fault Double Oven (Lower Oven).

Oven

F185

Door Open with Defective Door Lock Double Oven (Lower Oven).

Oven

F186

Door Lock Does Not Close Double Oven (Lower Oven).

Oven

F187

Door Lock Does Not Open Double Oven (Lower Oven).

Oven

F188

Spit Short Circuit Double Oven (Lower Oven).

Oven

F189

Over-Riding Time Control Over Run Double Oven (Lower Oven).

Oven

F195

Communication Fault with Radio Food Probe.

Oven

F5

Oven PT1000 Sensor Short Circuit

Stove

F6

Oven PT1000 Sensor Open Circuit

Stove

F7

Catalyser PT1000 Sensor Open Circuit

Stove

F9

PT1000 Kat Sensor Open Circuit

Stove

F21

Faulty Grill Heating Element

Stove

F22

Faulty Oven Fan Forced Element

Stove

F23

Pyrolysis Heating Fault

Stove

F30

Different Signal Between Door & Door Contact

Stove

F31

Door Open with Defective Door Lock

Stove

F31

Door Open with Defective Door Lock

Stove

F32

Door Lock Does Not Close

Stove

F33

Door Lock Does Not Open

Stove

F43

Model Type Not Programmed

Stove

F47

BAE / SLT Interface Defective

Stove

F48

BAE / O2 Sensor Interface Defective

Stove

F54

Spit Shot Circuit

Stove

F55

Over Riding Time Control Over Run

Stove

F57

Faulty Cooling Fan

Stove

F60

Faulty Hot Air Fan

Stove

F61

Excessive Temperature

Stove

F89

Faulty O2 Sensor

Stove

F90

Faulty O2 System

Stove

F102

Communication to Smart House Bus Failure

Stove

F103

Smart House Bus Link Incompatibility

Stove

F180

PT1000 Sensor Short Circuit Double Oven (Lower Oven)

Stove

F181

PT1000 Sensor Open Circuit Double Oven (Lower Oven)

Stove

F182

PT1000 Catalyser Sensor Short Circuit Double Oven (Lower Oven)

Stove

F183

PT1000 Catalyser Sensor Open Circuit Double Oven (Lower Oven).

Stove

F184

Pyrolysis Heating Fault Double Oven (Lower Oven).

Stove

F185

Door Open with Defective Door Lock Double Oven (Lower Oven).

Stove

F186

Door Lock Does Not Close Double Oven (Lower Oven).

Stove

F187

Door Lock Does Not Open Double Oven (Lower Oven).

Stove

F188

Spit Short Circuit Double Oven (Lower Oven).

Stove

F189

Over-Riding Time Control Over Run Double Oven (Lower Oven).

Stove

F195

Communication Fault with Radio Food Probe.

Stove

F5

Oven PT1000 Sensor Short Circuit

Microwave

F6

Oven PT1000 Sensor Open Circuit

Microwave

F7

Catalyser PT1000 Sensor Open Circuit

Microwave

F9

PT1000 Kat Sensor Open Circuited

Microwave

F32

Door Lock Doesn't Close

Microwave

F33

Door Lock Doesn't Open

Microwave

F109

Pump Fault

Microwave

F128

Communication Fault Oven Gen5000 Top Class and Moisture Electronic EPQF

Microwave

F129

Analysis Fault of Touch Electronic Oven Gen5000 SK

Microwave

F129

Analysis fault of touch electronic oven gen5000 sk

Microwave

F132

Sensor fault pt1000 steam producer

Microwave

F133

Short circuit t1000 steam producer

Microwave

F134

Unauthorised temperature excess

Microwave

F1

There is a fault inside the machine.

Coffee Machine

F2

Coffee/hot-water NTC open-circuited.

Coffee Machine

F3

Steam NTC (1R30) short-circuited.

Coffee Machine

F4

Steam NTC (1R30) open-circuited.

Coffee Machine

F10

No water intake.

Coffee Machine

F17

Insufficient water intake. Water tank installed incorrectly.

Coffee Machine

F28

There is too much coffee in the ground coffee chute.

Coffee Machine

F42

The fault displays for about 3 seconds when the appliance is switched on. Main power frequency (50Hz/60Hz) not set correctly.

Coffee Machine

F45

Electronic fault. Faulty flash RAM or incorrect data.

Coffee machine

F47

Communication fault between display electronic and power electronic.

Coffee machine

F71

Capsule magazine jammed.

Coffee machine

F72

Capsule transport jammed. The capsule magazine drawer is jammed by the capsule transport slide.

Coffee machine

F73

Brew unit jammed.

Coffee machine

F74

Ceramic valve fault.

Coffee machine

F75

Capsule not ejected after coffee preparation.

Coffee machine

F76

Capsule could not be pressed correctly onto the capsule plate or capsule not transported correctly to the brew unit.

Coffee machine

F77

Faulty initializing of ceramic valve.

Coffee machine

F77

Faulty initializing of ceramic valve.

Coffee Machine

F80

Coffee/hot-water heater is not heating - temperature is below 140°F.

Coffee Machine

F82

Coffee/hot-water heater is overheating due to a power electronic fault.

Coffee Machine

F83

Steam heater is overheating due to a power electronic fault.

Coffee Machine

F01

Water heater NTC short-circuited

Dishwasher

F02

Water heater NTC open circuit

Dishwasher

F11

Draining issue/Drain pump or filter blocked

Dishwasher

F12 / F13

Water intake error

Dishwasher

F14

Heater pressure switch fault

Dishwasher

F24

Heater relay fault

Dishwasher

F25

Heater fault

Dishwasher

F26

Water temperature too high

Dishwasher

F32

Door lock issue

Dishwasher

F51

Defective heater relay

Dishwasher

F53

Speed sensor fault

Dishwasher

F67

Circulation pump speed too slow

Dishwasher

F68

Circulation pump operates after switch off

Dishwasher

F70

Float switch error

Dishwasher

F78

Circulation pump error

Dishwasher

F88

Turbidity sensor fault

Dishwasher

F0

Faulty sensor for fresh air in "BioFresh

Fridge

F1

Faulty sensor in refrigerating chamber

Fridge

F2

Faulty evaporator sensor

Fridge

F3

Faulty air sensor in freezer compartment

Fridge

F4

Failure in evaporator sensor

Fridge

F5

Malfunction in microprocessor control card

Fridge

01_F_21

Ice fault

Fridge

E01

Door unlocked - The door is not locked properly.

Washing Machine

E02

Water filling issue - The water inlet valve may be faulty.

Washing Machine

E03

Pump failure - The pump may not be working correctly.

Washing Machine

E04

Overflow error - There may be a leak in the machine.

Washing Machine

E05

NTC or heater error - There may be a problem with the NTC or the heater.

Washing Machine

E06

Motor failure - There may be an open circuit, short circuit or disconnected motor issue.

Washing Machine

E08

Motor triac short circuit - There may be an issue with the motor triac.

Washing Machine

E08

Motor triac short circuit - An issue with the motor triac has been detected.

Washing Machine

H01

Water level sensor error - There's a problem with the water level sensor.

Washing Machine

H02

Motor triac error - There's a problem with the motor triac.

Washing Machine

H04

Load relay short circuit error - There's a problem with the load relay circuit.

Washing Machine

H05

Memory circuit of IC issue - There's a problem with the memory circuit of the IC.

Washing Machine

H12

Safety switch connection error - There's a problem with the safety switch connection.

Washing Machine

H17

Thermistor error (for X series) - The thermistor sensor in the X series has detected an irregular signal or is out of range.

Washing Machine

H18

Motor thermistor sensor detected irregular signal or out of range - Check motor connections.

Washing Machine

H21

Overflow error - There is an issue with water overflowing in the washing machine.

Washing Machine

H23

Heater relay on main control PCB detected abnormal or out of range - There is probably an issue with the electronic controller.

Washing Machine

H25

Motor error - There is a possible main motor wiring problem.

Washing Machine

H27

The washing machine door lock cannot engage with the latch in place - The door lock cannot lock with the latch in its current position.

Washing Machine

U12

The door is not shut properly, close it securely and press start button

Dryer

U15

The water container is full, empty it and set the water drain hose properly, turn the power on and press start button

Dryer

U30

Operate the appliance within the operating temperature range of 5 ºC - 35 ºC

Dryer

H*

Inspection is required, pull out the power plug and contact customer service with the displayed content (2-digit number after H)

Dryer

H99

Error in inverter's on/off control

Oven

H98

Magnetron has no oscillation

Oven

H97

Error in inverter input

Oven

H96

Error in custom IC inverter

Oven

H95

Failure in inverter input

Oven

H90

Inverter thermistor controls power down

Oven

H44

Failure in keyboard switch

Oven

H39

Failure in steam heater thermistor

Oven

H32

Failure in magnetron thermistor

Oven

H30

Failure in oven thermistor

Oven

H02

Memory IC error, may appear in test or cooking mode.

Oven

H00

RAM failure, may appear in test or cooking mode.

Oven

H20

Steam heater open error.

Oven

U14

No water during steam cooking, may appear in test or cooking mode.

Oven

U40

No load operation.

Oven

U65

Thermistor-controlled power down by magnetron.

Oven

HOT

Oven is hot, may appear in test or cooking mode.

Oven

F33

Open temperature sensor (exhaust).

Oven

F34

Short temperature sensor (exhaust), rare.

Oven

F44

Shorted membrane switch.

Oven

F01

Exhaust temperature exceeds 120°C (260°F); food is overcooked.

Oven

F05

Failure in digital programmer circuit.

Oven

F09

Oven designed for 50Hz is operated in a 60Hz environment; controller board failure.

Oven

F81

Excessive current consumption in upper H.V. circuit.

Oven

F82

Excessive current consumption in lower H.V. circuit.

Oven

F86

Relay failure in RY-3; shorted contacts; digital programmer circuit failure.

Oven

F87

Shorted contacts in RY-4.

Oven

H02

Memory IC error (can occur in both test and cooking modes).

Microwave

H00

RAM failure (can occur in both test and cooking modes).

Microwave

H20

Steam heater open error.

Microwave

U14

No water during steam cooking (can occur in both test and cooking modes).

Microwave

U40

No load operation.

Microwave

U65

Power down controlled by magnetron thermistor.

Microwave

H99

Inverter on/off control error.

Microwave

H98

Magnetron no oscillation error.

Microwave

H97

Inverter input error.

Microwave

H96

Inverter custom IC error.

Microwave

H95

Inverter input failure.

Microwave

H90

Power down controlled by Inverter thermistor.

Microwave

H44

Keyboard switch failure.

Microwave

H39

Steam heater thermistor failure.

Microwave

H32

Magnetron thermistor failure.

Microwave

H12

Inappropriate device capacities

Heat pump

H15

Fault with compressor temperature sensor

Heat pump

H20

Fault with circulation pump

Heat pump

H23

Fault with coolant sensor

Heat pump

H27

Fault with service valve

Heat pump

H28

Fault with solar sensor

Heat pump

H31

Fault with swimming pool sensor

Heat pump

H36

Fault with buffer tank sensor

Heat pump

H38

Fault due to non-matching device brands

Heat pump

H62

Fault with upstream with the flow monitor.

H63

Fault with the low pressure sensor.

H64

Fault with the high pressure sensor.

H65

Fault with the water circulation during defrosting.

H67

Fault with outdoor temperature sensor 1.

H68

Fault with outdoor temperature sensor 2.

H70

Fault with overload protection for indoor units E-heating element.

H72

Fault with hot water tank temperature sensor.

H74

Fault with the PCB communication.

H75

Low water temperature protection.

H76

Fault with the PCB communication.

H90

Communication fault.

H91

Fault with overload protection for hot water E-heating.

Heat pump

H95

Fault with incorrect voltage IU - OU.

Heat pump

H98

Fault due to high pressure protection.

Heat pump

H99

Fault due to frost protection of indoor units heat exchanger.

Heat pump

F12

High pressure switch in the outdoor unit triggered.

Heat pump

F14

Incorrect compressor speed.

Heat pump

F15

Incorrect speed of the OU fan motor.

Heat pump

F16

Fault due to excessive current consumption.

Heat pump

F20

Fault due to overload protection of the compressor.

Heat pump

F20

Fault due to overload protection of the compressor.

Heat pump

F22

Fault due to overload protection of power transistor.

Heat pump

F23

Fault due to direct current peaks in the outdoor unit.

Heat pump

F24

Fault due to problems in the cooling circuit.

Heat pump

F25

Fault due to problems with the switching interval.

Heat pump

F27

Fault with the high pressure switch in the outdoor unit.

Heat pump

F29

Low hot gas superheat.

Heat pump

F30

Fault with the inflow temperature sensor.

Heat pump

F32

Fault with the room thermostat.

Heat pump

F36

Fault with the outdoor temperature sensor.

Heat Pump

F37

Fault with the return flow temperature sensor.

Heat Pump

F40

Fault with the hot gas temperature sensor in the outdoor unit.

Heat Pump

F41

Error in the power factor correction.

Heat Pump

F42

Error with the heat exchanger sensor in the outdoor unit.

Heat Pump

F43

Fault with hot gas temperature sensor in the outdoor unit.

Heat Pump

F43

Fault with hot gas temperature sensor in the outdoor unit.

Microwave

F45

Fault with the defrost temperature sensor in the outdoor unit.

Microwave

F46

Current transformer switching off.

Microwave

F48

Error with evaporator outlet temperature sensor.

Microwave

F49

Fault with bypass outlet temperature sensor in the OU.

Microwave

F95

Fault due to HP protection cooling in the outdoor unit.

Microwave

E1

Long water inlet time

Coffee Machine

E3

Heating Abnormal

Coffee Machine

E4

Water overflow

Coffee Machine

E6

Failure of Varistor

Coffee Machine

E7

Failure of Varistor

Coffee Machine

E8

Failure of Orientation of Distributary Valve

Coffee Machine

E1

Water filling exceeded pre-set time

Dishwasher

E3

Heating exceeded pre-set time

Dishwasher

E4

Overflow

Dishwasher

E6

Open-circuit failure of thermistor

Dishwasher

E7

Short-circuit failure of thermistor

Dishwasher

Sr

Failure/Warning

LF

Freezer compartment is not cold enough.

LC

Refrigerator compartment is not cold enough.

LF and LC

Not cold enough.

HC

Refrigerator compartment is too cold.

LOPO

Low voltage.

F1

LED 4 shows a short circuit in the washing machine's motor, requiring an expert to examine it.

Washing Machine

F2

LED 3 shows either a jammed motor or a faulty tacho. A technician is required to check.

Washing Machine

F3

LED 3 & 4 indicate a problem with the NTC thermistor, which could be faulty or have a loose connection.

Washing Machine

F4

LED 2 shows the pressure switch is jammed on empty. A repair technician is needed to diagnose the issue.

Washing Machine

F5

LED 2 & 4 indicate the pressure switch is jammed on full. A repair technician is needed to diagnose the issue.

Washing Machine

F7

LED 2, 3 & 5 indicate a problem with the heating system in the washing machine.

Washing Machine

F9

LED 1 & 4 indicate a major problem with the machine's set-up, requiring re-programming or electronics replacement.

Washing Machine

F10

LED 1 & 3 indicate a complex problem with the pressure switch sensor, requiring professional attention.

Washing Machine

F11

LED 1, 3 & 4 show that the washing machine pump is not working, likely requiring connections between the pump and module repair or pump replacement.

Washing Machine

F12

LED 1 & 2 indicate an electrical connection problem with a faulty cable between the control cards in the washing machine.

Washing Machine

F13

LED 1, 2 & 4 indicate an overheated machine in a Washer-Dryer, which could just need the lint filter cleaning or have a faulty dryer motor.

Washer-Dryer

F14

LED 1, 2 & 3 indicate a dryer not heating in a Washer-Dryer, which could be due to the thermostat, heating element, fan motor or module connections.

Washer-Dryer

F15

LED 1, 2, 3 & 4 flashing indicate a problem with the dryer element in a Washer-Dryer.

Washer-Dryer

F17

LED 4 & 5 show a door lock failure in the washing machine, requiring a professional investigation.

Washing Machine

F18

LED 3 indicates a communication error on the 3-phase motor, requiring a qualified repair technician to replace the power board.

Washing Machine

F02

Motor circuit fault. Intermittent or no drum rotation during wash cycle. Call customer service to book an engineer.

Dryer

F03

Temperature sensing fault. Tumble dryers not heating on wash or dry settings. Call customer service to book an engineer.

Dryer

F05

Waste pipe blockage or pump issue. Tumble dryers door will not open or water remains in the drum. Check for blockages in pump filter and waste water hose, or call customer service to book an engineer for pump failure.

Dryer

F06

Door lock fault. Tumble dryers door cannot be opened or closed, or the machine will not start when the door is closed. Check for obstructions in the door lock or call customer service to book an engineer.

Dryer

F07

Electronic circuit board fault / heating circuit fault. The programme pauses part way through the wash cycle or the machine is not heating and the pump runs continuously.

Dryer

F07

Electronic circuit board fault / heating circuit fault, during a wash cycle the programme pauses part way through/ the machine is not heating and the pump runs continuously

Dryer

F08

During a wash cycle the programme pauses part way through

Dryer

F09

Tumble Dryers isn’t operating multiple flashing lights and/or display. Unable to select a programme.

Dryer

F11

Water remains in Tumble Dryers / not pumping out. Call customer service to book an engineer

Dryer

F12

Tumble Dryers is not operating (turning on). Call customer service to book an engineer

Dryer

F13

Washer dryer is not drying clothes

Dryer

F16

Tumble Dryers drum is stopping in the wrong position or is not locked in the correct position

Dryer

F18

Internal data error, some or all display/functions do not work on the tumble dryer

Dryer

F01

Short circuit motor triac.

Oven

F02

Motor jammed or fan blocked.

Oven

F03

Front thermistor open/short circuit.

Oven

F04

No pump piloting.

Oven

F05

No feedback from the pump.

Oven

F08

Static heater relay with contact welded closed.

Oven

F09

Eprom is not programmed or not functioning.

Oven

F10

Common of heater open or one shot open.

Oven

F11

No pump connection.

Oven

F11

No pump connection.

Oven

F12

Communication error between boards.

Oven

F13

Rear thermistor open/short circuit.

Oven

F15

Dynamic heater relay with contact welded closed.

Oven

F17

Master relay welded closed.

Oven

F01

Short circuit motor triac - There is a problem with the motor triac circuitry.

Oven

F02

Motor jammed or fan blocked - The motor is jammed or the fan is blocked.

Oven

F03

Front thermistor open/short circuit - There is an open or short circuit in the front thermistor.

Oven

F04

No pump piloting - The pump is not being controlled properly.

Oven

F05

No feedback from the pump - The pump is not providing feedback to the control board.

Oven

F08

Static heater relay with contact welded closed - There is a problem with the heater relay circuitry.

Oven

F09

Eprom is not programmed or not functioning - There is a problem with the eprom circuitry.

Oven

F10

Common of heater open or one shot open - There is a problem with the heater circuitry.

Oven

F10

Heat-sink NTC failure.

Oven

F11-1

Heat-sink NTC short circuit.

Oven

F11-2

Heat-sink NTC open circuit.

Oven

F12-1

Heat-sink temperature is too high.

Oven

F13-1

Rear inductor temperature is too high.

Oven

F14-1

Large hob temperature is too high.

Oven

F15-1

Small hob temperature is too high.

Oven

F16-1

Large hob temperature sensor failure.

Oven

F17-1

Small hob temperature sensor failure.

Oven

F17 - 1

The small hob has exceeded the maximum temperature limit. Verify that the inductor NTC is calibrated and replace the inductor if necessary. Replace the power board if the problem persists.

Oven

F18 - 1

Communication between Visual Board and External Board is not working.

Oven

F19 - 1

Communication between Visual Board and External Board is not working.

Oven

F10

The dishwasher could not fill or empty within the set time.

Oven

F11

The dishwasher's heater was unable to reach the required temperature level.

Oven

F20

The dishwasher's temperature is too low.

Oven

F21

The dishwasher's temperature is too high.

Oven

A01

The float switch has been activated.

Oven

A02

There is a problem with the heater relay.

Oven

A03

There is a short circuit with the thermistor.

Oven

A04

The dishwasher has been unable to sense or reach the correct temperature within 70 minutes.

Oven

A05

The pressure switch has not been reset.

Oven

A14

The drain hose is too low and causing syphoning. Check the drain hose and re-adjust.

Dishwasher

H20

Check the tap and water pressure coming into the dishwasher.

Dishwasher

A05

The pressure switch has not been reset.

Dishwasher

A07

There is a problem with the wash motor triac.

Dishwasher

A08

There is a problem with the auxiliary wash motor triac.

Dishwasher

A09

There is a problem with the main wash triac.

Dishwasher

A10

There is a problem with the fill valve triac.

Dishwasher

A11

There is a problem with the half load valve triac or alternating motor action.

Dishwasher

A12

There is an open circuit with the heater relay.

Dishwasher

A13

There is a problem with the dispenser triac.

Dishwasher

F1

The freezer temperature sensor is not working.

Fridge

F2

The freezer temperature sensor has a short circuit.

Fridge

F3

The fridge temperature sensor is not working.

Fridge

F4

The fridge temperature sensor has a short circuit.

Fridge

F7

The evaporator temperature sensor is not working.

Fridge

F8

The evaporator temperature sensor has a short circuit.

Fridge

F9

The temperature set switch is not working.

Fridge

FA

There is no feedback from the baffle.

Fridge

FB

The fridge baffle motor is operating continuously.

Fridge

FE

The defrost time has timed out.

Fridge

IE

The washing machine wasn't able to reach the correct water level within 8 minutes of water being supplied, or it didn't reach the set water level within 20 minutes.

Washing Machine

UE

The load is too small, the washing machine is tilted, laundry is gathered to one side, or non-distributable items are in the drum.

Washing Machine

0E

Water is overflowing. If 0E is displayed, the drain pump will automatically drain the water.

Washing Machine

FE

Water is overflowing. If FE is displayed, the drain pump will automatically drain the water.

Washing Machine

PE

The pressure sensor assembly is not working properly. The water level frequency is consistently below 10 kHz or over 30kHz.

Washing Machine

dE1, dE2

The door is not completely closed, there are loose electrical connections at the door switch and PWB Assembly, or the door switch assembly is not working properly.

Washing Machine

tE

The thermistor is not working properly.

Washing Machine

LE

There is a problem with the connection between the motor and stator assembly, the electric contact between the connectors in the motor harness and main PWB assembly is bad or unstable, or the motor harness is cut.

Washing Machine

EE

The EEPROM is not working properly and is displayed only when the start/pause button is first pressed in the load test mode.

Washing Machine

PF

The power was rapidly supplied while the machine was working.

Washing Machine

Sud

The washing machine detected too many suds and displays this error code. A suds reducing cycle is added, which adds about two hours to the cycle time. If too many suds are detected during spinning, the washing machine stops to prevent leaking.

Washing Machine

nE

The WiFi modem is not connected.

Washing Machine

nF

There is an error with the WiFi modem self-check function.

Washing Machine

FF

Supply warm water into the drum, unfreeze the drain hose and drain pump. Wet a towel in warm water and apply it to the supply hose.

Washing Machine

vS

There is a malfunction with the vibration sensor. Replace the vibration sensor.

Washing Machine

dE

The dryer door does not close properly.

Dryer

dE4

The dryer's door switch detection system is not functioning properly.

Dryer

tE1, tE2, or tE4

The dryer's temperature sensor is not working properly.

Dryer

F1

The temperature inside the dryer drum is too high.

Dryer

LE1

The dryer's motor has stopped working.

Dryer

LE2 or AE

The dryer's compressor is not working properly.

Dryer

OE

The motor of the dryer's drain pump has malfunctioned or the ambient temperature is too low.

Dryer

F1

Oven sensor remains open for over 60 seconds during cooking.

Oven

F2

Oven sensor is shorted for over 60 seconds during cooking.

Oven

F3

Some oven keys are short-circuited.

Oven

F6

The oven temperature is too high.

Oven

F9

The oven is not heating up to the set temperature.

Oven

F8

The right oven probe sensor is short-circuited.

Oven

F10

There is a failure with the door lock motor.

Oven

F11

A communication error occurred between cooktop and oven PCB.

Oven

CF1

LF top sensor is open or short-circuited.

Oven

CF2

LR top sensor is open or short-circuited.

Oven

CF3

RF top sensor is open or short-circuited.

Oven

CF4

RR top sensor is open or short-circuited.

Oven

CF5

Left IGBT sensor is open or short-circuited.

Oven

CF6

Right IGBT sensor is open or short-circuited.

Oven

CF7

Left communication error.

Oven

CF8

Right communication error.

Oven

CFA

Overcurrent error.

Oven

CFC

Overvoltage error.

Oven

CFF

Box fan not working properly.

Oven

F7

Convection fan operating cannot be detected.

Oven

F27

The cooling fan is stalled during self-clean.

Oven

F1F4

Oven thermistor is open.

Oven

F2F5

Oven thermistor is short-circuited.

Oven

F6F16

The oven temperature is too high.

Oven

F18

The lower oven probe is short-circuited.

Oven

F9F19

The oven is not heating up to the set temperature.

Oven

F10F20

There is a failure with the door lock motor.

Oven

F4

Oven thermistor remains open for over 60 seconds during cooking.

Oven

F5

Oven thermistor is short-circuited for over 60 seconds during cooking.

Oven

F16

The oven temperature is too high.

Oven

F16

The oven temperature is too high.

Oven

F19

The oven is not heating up to the set temperature.

Oven

F20

There is a failure with the door lock motor.

Oven

F24

Steam thermistor remains open for 10 seconds after steam heater operation.

Oven

F25

Steam thermistor is short-circuited for over 60 seconds after steam heater operation.

Oven

F19

The oven is not heating up to the set temperature.

Oven

cf1

LF top sensor is open or short-circuited.

Stove

cf2

LR top sensor is open or short-circuited.

Stove

cf3

RF top sensor is open or short-circuited.

Stove

cf4

RR top sensor is open or short-circuited.

Stove

CF5

Left IGBT sensor is open or short-circuited.

Stove

CF6

Right IGBT sensor is open or short-circuited.

Stove

CF7

Left communication error.

Stove

CF8

Right communication error.

Stove

CFA

Overcurrent error.

Stove

F8

The right oven probe sensor is short-circuited.

Oven

F18

The lower oven probe is short-circuited.

Oven

F10

There is a failure with the door lock motor.

Oven

F20

There is a failure with the door lock motor.

Oven

F24

The steam thermistor remains open for 10 seconds after steam heater operation.

Oven

F25

The steam thermistor is short-circuited for over 60 seconds after the steam heater operation.

Oven

F11

A communication error occurred between the cooktop and oven PCB.

Oven

CF1

The LF top sensor is open or short-circuited.

Oven

f1

Oven sensor (thermistor) remains open for over 1 minute during cooking.

Oven

f2

Oven sensor (thermistor) is short for over 1 minute during cooking.

Oven

f3

When some keys are continuously short for over 60 seconds.

Oven

f4

Oven thermistor remains open for over 60 seconds during cooking.

Oven

f5

Oven thermistor is short-circuited for over 60 seconds during cooking.

Oven

f6

The oven temperature is too high.

Oven

CFC

Overvoltage occurs at the cooktop.

Stove

CFF

Box fan not working properly.

Stove

F7

Convection fan operating cannot be detected.

Stove

F27

When cooling fan is stalled during self-clean.

Stove

F1F4

Oven thermistor is open.

Stove

F2F5

Oven thermistor is short-circuited.

Stove

f16

The oven temperature is too high.

Oven

f9

The oven is not heating up to the set temperature.

Oven

f19

The oven is not heating up to the set temperature.

Oven

Childlock

The child lock feature is enabled and the microwave cannot be operated without disabling it.

Microwave

F-1 Key Error

The key for controlling the microwave has malfunctioned or is stuck.

Microwave

F-5 Humidity Sensor Error

The humidity sensor has malfunctioned and the microwave cannot detect moisture in the food.

Microwave

F-11 Inverter Communication Error

There is a communication error between the inverter and the control board of the microwave.

Microwave

F-13 Inverter Over Current

The inverter has detected an over current error and has shut down to prevent damage to the microwave.

Microwave

F-14 Inverter Over Voltage

The inverter has detected an over voltage error and has shut down to prevent damage to the microwave.

Microwave

F-15 Inverter Over Current

The inverter has detected an over current error and has shut down to prevent damage to the microwave.

Microwave

F-16 Inverter Heat Sink Error

The heat sink of the inverter has malfunctioned, causing the microwave to shut down to prevent damage.

Microwave

F-16

Inverter heat sink error.

Microwave

F-17

Inverter temperature sensor error.

Microwave

F-19

Inverter VDC protection error.

Microwave

60

Outdoor unit PCB EEPROM check sum error.

Heat pump

61

Outdoor unit condenser coil temperature is too high.

Heat pump

62

Outdoor unit inverter compressor PCB heat sink temperature is too high.

Heat pump

63

Condenser coil pipe thermistor temperature is too low.

Heat pump

65

Heat sink thermistor has disconnected or has shorted out.

Heat pump

67

Outdoor BLDC fan motor lock error.

Heat pump

32

Inverter compressor discharge pipe temperature is too high.

Heat pump

40

Current transformer (CT) thermistor has disconnected or has shorted out.

Heat pump

41

Inverter compressor discharge pipe thermistor has disconnected or has shorted out.

Heat pump

44

Outdoor unit inlet air thermistor has disconnected or has shorted out.

Heat pump

45

Outdoor unit condenser coil middle thermistor has disconnected or has shorted out.

Heat pump

46

Outdoor unit suction line thermistor has disconnected or has shorted out.

Heat pump

48

Outdoor unit coil outlet (liquid line) thermistor has disconnected or has shorted out.

Heat pump

53

Communication failure from outdoor unit to indoor unit.

Heat pump

22

Current transformer2 (CT2) error; AC input current is too high.

Heat pump

23

DC link voltage is too low.

Heat pump

25

Voltage to the system is too low or too high.

Heat pump

26

Inverter compressor has seized up or is not providing rotation.

Heat pump

27

Prospective short circuit (PSC) fault error; current to inverter compressor between AC and DC converter circuit is too high.

Heat pump

28

Inverter compressor DC voltage is too high.

Heat pump

29

Inverter compressor amperage is too high.

Heat pump

31

Current to the current transformer (CT) thermistor is too low.

Heat pump

32

Inverter compressor discharge pipe temperature is too high.

Heat pump

1

Indoor unit return air thermistor has disconnected or has shorted out.

Heat Pump

2

Indoor unit inlet pipe thermistor has disconnected or has shorted out.

Heat Pump

5

Communication failure from indoor unit to outdoor unit.

Heat Pump

6

Indoor unit outlet pipe thermistor has disconnected or has shorted out.

Heat Pump

9

Indoor unit EEPROM error.

Heat Pump

10

Indoor unit fan has locked up (fan motor operation failure).

Heat Pump

12

Indoor unit middle pipe thermistor has disconnected or has shorted out.

Heat Pump

21

DC peak error / IPM fault; compressor DC voltage was too high.

Heat Pump

OE

The dishwasher has detected a drain issue, often resulting from food clogs or installation problems.

Dishwasher

IE

The water level in the dishwasher did not get high enough after 10 minutes of filling.

Dishwasher

2H

This is an indicator of the estimated time remaining for the cycle.

Dishwasher

LE or CE

This indicates a motor error.

Dishwasher

CR

This indicates that the unit is in TEST MODE used by installers and service technicians to check the functionality of the unit.

Dishwasher

bE

This indicates the use of improper detergent or failure to level the appliance.

Dishwasher

FE

This error indicates that the dishwasher has experienced a fill error.

Dishwasher

HE

The unit has had a heater error.

Dishwasher

nE

This displays when the unit detects a possible issue with the vario motor, which controls the dishwasher's spray arms.

Dishwasher

PF

This is designed to protect the dishwasher in the case of a power outage or interruptions.

Dishwasher

tE

The unit has experienced a Thermal Error. This will occur if the water temperature is above 194 degrees, or if there is a problem with the thermistor.

Dishwasher

CL

Child Lock

Dishwasher

dHF

Freezer defrosting error

Fridge

FFE

Freezer fan motor is not working properly

Fridge

CFE

Mechanic room fan motor is not working properly

Fridge

COE

Communication error between main and display computer

Fridge

rAS

Auto drawer reed switch (right) is not working properly.

Fridge

EC1

Communication error between main and dispenser computer.

Fridge

ErC1

Communication error between top display and dispenser computer.

Fridge

dSF

Freezer defrosting sensor is not working properly.

Fridge

HSE

Humidity sensor is not working properly.

Fridge

ISE

Icing sensor is not working properly.

Fridge

SSE

Pantry sensor is not working properly.

Fridge

rtE

Room temperature sensor is not working properly.

Fridge

ItE

Ice maker kit is not working properly.

Fridge

Ett

Water tank switch is not working properly.

Fridge

EdS

Defrosting sensor is not working properly.

Fridge

ECS

Convertible sensor is not working properly.

Fridge

Ead

Auto door module is not working properly.

Fridge

EAS

Auto door reed switch is not working properly.

Fridge

EdL

Auto drawer module (left) is not working properly.

Fridge

LAS

Auto drawer reed switch (left) is not working properly.

Fridge

Edr

Auto drawer module (right) is not working properly.

Fridge

rAS

Auto drawer reed switch (right) is not working properly.

Fridge

ECO

Communication error between main and display computer.

Fridge

ESd

Communication error between main and sub computer.

Fridge

EOd

Wi-Fi modem error.

Fridge

ECH

High side refrigerant leak detected.

Fridge

ECL

Low side refrigerant leak detected.

Fridge

rdS

Refrigerator defrost sensor is not working properly.

Fridge

ErF

Refrigerator fan motor is not working properly.

Fridge

EUC

UV Nano LED module is not working properly.

Fridge

Elt

Ice maker unit is not working properly.

Fridge

LOC

Control Lock function has been enabled. To resolve, touch the Control Lock button or refer to the manual for activation instructions.

Washing Machine

LC

The Control Lock feature has been activated. To resolve, touch the Control Lock button or consult the manual for instructions on activation.

Washing Machine

dET

Detergent cartridge not detected. Ensure it's inserted properly and dispenser drawer is shut.

Washing Machine

Int

Cycle was paused or canceled. Press pause or cancel button twice and power button once to remove code.

Washing Machine

rL

During Clean Washer cycle, items were detected in the drum. Remove the items and restart the cycle.

Washing Machine

F34

During Clean Washer cycle, items were detected in the drum. Remove the items and restart the cycle.

Washing Machine

Sud

The machine has too many suds. Try using HE detergent, inspect the drain hose, and use regular liquid bleach instead of "no splash" or "easy pour".

Washing Machine

Sd

An excessive amount of suds is present in the machine. Consider using HE detergents, examining the drain hose, and switching to regular liquid bleach instead of "no splash" or "easy pour".

Washing Machine

F5

The door is not securely closing. Look for any items blocking the door and hit the Pause or Cancel button twice and the Power button once to reset the code.

Washing Machine

E2

The door is not properly locking. Check for any objects blocking the door and press the Pause or Cancel button twice and the Power button once to clear the code.

Washing Machine

E1

Motor speed sensing issue detected. Please remove shipping bolts and inspect for any overloads. To clear the code, press the Pause or Cancel button twice and the Power button once.

Washing Machine

F7

A problem with the motor speed sensing has been detected. Please remove any shipping bolts and inspect the machine for overloads. To clear the code, press the Pause or Cancel button twice followed by the Power button once.

Washing Machine

F8

Indicates a low water flow. Ensure the water supply is turned on and the inlet hoses are not kinked. Clear the code by pressing the Pause or Cancel button twice and the Power button once.

Washing Machine

E1

Indicates low water flow. Check that the water supply is on and the hoses are not kinked. Clear the code by pressing the Pause or Cancel button twice and the Power button once.

Washing Machine

LO

Signals low water flow. Make sure the water supply is on and the hoses are not obstructed. Clear the code by pressing the Pause or Cancel button twice and the Power button once.

Washing Machine

FL

Indicates a shortage of water flow. Check the water supply and hoses to make sure they are not obstructed. Clear the code by pressing the Pause or Cancel button twice and the Power button once.

Washing Machine

F9

Draining taking longer than anticipated, typically over 8 minutes. Verify drain hose isn't kinked or clogged, and standpipe height is between 39" and 96". Ensure HE detergent is used and check for excessive suds.

Whirlpool Washing Machine

E1

Draining taking longer than expected, usually over 8 minutes. Check the drain hose and make sure it's not obstructed or blocked, and the standpipe height is between 39" and 96". Use HE detergent and look for excessive suds as well.

Whirlpool Washing Machine

F08

During a wash cycle the programme pauses part way through.

Washing Machine

F12

Washing Machines is not operating (turning on).

Washing Machine

F02

Intermittent or no drum rotation during wash cycle.

Washing Machine

F01

Electronic circuit board fault - Tumble Dryers is not operating, some or all functions are not selectable.

Dryer

F02

Motor circuit fault - Intermittent or no drum rotation during wash cycle.

Dryer

F03

Temperature sensing fault - Tumble Dryers not heating on wash or dry settings.

Dryer

F05

Waste pipe blockage or pump issue - Tumble Dryers door will not open / the door can be opened but water remains inside the drum.

Dryer

F06

Door lock fault - Tumble Dryers door cannot be opened or closed / when the door is closed the machine the programme will not start.

Dryer

F07

Electronic circuit board fault / heating circuit fault - During a wash cycle the programme pauses part way through / the machine is not heating and the pump runs continuously.

Dryer

F08

Heater fault - During a wash cycle the programme pauses part way through.

Dryer

F09

Tumble Dryers isn’t operating multiple flashing lights and/or display. Unable to select a programme.

Dryer

F11

Water remains in Tumble Dryers / not pumping out.

Dryer

F12

Tumble Dryers is not operating (turning on).

Dryer

F13

Washer dryer is not drying clothes.

Dryer

F15

Tumble Dryers is not heating water or pauses during a wash cycle / not drying or pauses during drying cycle.

Dryer

F16

Tumble Dryers drum is stopping in the wrong position or is not locked in the correct position.

Dryer

F18

Some or all display / functions do not work on my tumble dryers.

Dryer

F19

Tumble Dryers is not drying / stops during drying cycle.

Dryer

F1, F5, F7, F8, F2-E0, F2-E5

Control board and keypad malfunction.

Oven

F3, F4, F3-E1, F3-E2, F3-E3

The oven temperature sensor has failed.

Oven

F9, F5-E0

The oven temperature is too high (Bake or Clean mode).

Oven

F2, F3-E2, F3-E3

There is an oven door lock malfunction.

Oven

F41

Burner 4 has an open circuit on the thermocouple.

Stove

F12

The PWM valve for burner 1 is stuck open.

Stove

F22

The PWM valve for burner 2 is stuck open.

Stove

F32

The PWM valve for burner 3 is stuck open.

Stove

F42

The PWM valve for burner 4 is stuck open.

Stove

F01

On/off valve stuck open.

Stove

F02

Communication problem.

Stove

F03

Control board problem.

Stove

F04

User interface problem.

Stove

F05

Continuous E2 EEPROM reset.

Stove

F11

Burner 1 open circuit on thermocouple.

Stove

F21

Burner 2 open circuit on thermocouple.

Stove

F31

Burner 3 open circuit on thermocouple.

Stove

F41

Burner 4 open circuit on thermocouple.

Stove

ERR B

The weight sensor is not detecting any pulses or the frequency is too low.

Microwave

ERR C

The temperature sensor is not working properly, it's not measuring temperatures between 19-41C.

Microwave

ERR D

There's a problem with a special protection system on the Microwave Magnetron.

Microwave

ERR0

There's a problem with the temperature in the oven, the connection is missing or has a short circuit.

Microwave

ERR1

There's a problem with the Microwave Relay having a short circuit.

Microwave

ERR3

If you press a button for more than 1 minute, there is a key error.

Microwave

ERR6

The weight sensor needs to be calibrated.

Microwave

ERR7

The humidity sensor is either broken or not connected.

Microwave

ERR8

It's impossible to write something in a specific computer memory.

Microwave

ERR9

A specific option has not been set.

Microwave

ERR A

The weight sensor cannot detect the wheel.

Microwave

F1, F5, F7, F8, F2-E0, F2-E5

There is a control-related part failure, stuck or defective keypad.

Heat Pump

F3, F4, F3-E1, F3-E2, F3-E3

Oven temperature sensor has failed.

Heat Pump

F9, F5-E0

Oven temperature is too high (Bake or Clean mode).

Main control board, temperature sensor, wire harness.

Heat Pump

F2, F3-E2, F3-E3

Oven door lock malfunction.

Door lock assembly, door switch, wire harness.

Heat Pump

F02

The solenoid valve that fills the dishwasher with water has failed.

Dishwasher

F03

There is a problem with the dishwasher's ability to drain water or there is a timeout while trying to drain water.

Dishwasher

F04

The dishwasher's thermostat is not working properly.

Dishwasher

F06

There is a timeout while filling the dishwasher with water.

Dishwasher

F07

The water turbine in the dishwasher is damaged.

Dishwasher

F08

There is a timeout related to temperature in the dishwasher.

Dishwasher

F09

There is an error in the dishwasher's software.

Dishwasher

F10

The heating element in the dishwasher is faulty.

Dishwasher

F11

There's a problem with the washing pump.

Dishwasher

F12

There's a problem with the dishwasher's display.

Dishwasher

F13

There's a problem with the dishwasher's main board.

Dishwasher

F15

There's something wrong with the virtual sensor.

Dishwasher

F01

The dishwasher is having an overflow problem.

Dishwasher

E9

The freezer is too warm, and the temperature alarm is activated.

Refrigerator

EE

There's a problem with the ice maker's circuit (if fitted).

Refrigerator

E0

There is a problem with the ice maker (if fitted).

Fridge

E1

The fridge sensor is not working properly.

Fridge

E2

The freezer sensor is not working properly.

Fridge

E3

The defrost sensor is not working properly.

Fridge

E4

The fridge defrost sensor is not working properly.

Fridge

E5

The freezer defrost sensor is not working properly.

Fridge

E6

There is a problem with the main control-board and display board.

Fridge

E7

The environmental temperature sensor is not working properly.

Fridge

E8

The environmental temperature sensor is not working properly.

Fridge

FH

No water detected entering the machine or the pressure switch was not detected.

Washing Machine

F02

A long drain time has been detected.

Washing Machine

F05

There is an error with the water temperature sensor.

Washing Machine

F06

An error with the drive motor tachometer has been detected.

Washing Machine

F07

There is an error with the motor control unit.

Washing Machine

F09

An overflow condition has been detected.

Washing Machine

F10

The motor control unit's heat sink has tripped due to overheating.

Washing Machine

F11

A serial communication error has occurred.

Washing Machine

F13

An error has been detected in the dispenser circuit.

Washing Machine

F14

An error with the EEPROM has been detected.

Washing Machine

F15

An error with the motor control unit has been detected.

Washing Machine

F21 or F22

An error has been detected in the CCU, Touchpad, or LED assembly.

Washing Machine

FdU

A door unlock error has been detected.

Washing Machine

FdL

A door lock error has been detected.

Washing Machine

Sud

A suds lock has been detected, meaning there was an overdose of detergent during the wash cycle.

Washing Machine

PF

Power failure - this means the dryer stopped working due to a power failure. Press Start to continue or press Pause/Cancel to stop it.

Dryer

E1

Temperature sensor open - this means the temperature sensing circuit is open and the temperature sensor needs to be replaced if faulty.

Dryer

E2

Temperature sensor shorted - this means the temperature sensing circuit is shorted and the temperature sensor needs to be replaced if faulty.

Dryer

E3

Blower rotation failure - if the blower rotation speed drops below 500 rpms, all outputs will be turned off and error code E3 will be displayed.

Dryer

E4

Tumbler rotation failure - if the tumbler rotation speed drops to 0, all outputs will be turned off and error code E4 will be displayed.

Dryer

E5

Dry rack sensor - if during a Dry Rack cycle the signal is lost, all outputs are turned off and error code E5 is displayed.

Dryer

E6

Exhaust high limit fault - if the exhaust temperature goes above 87.7C (190F) all outputs will turn off and error code E6 will be displayed.

Dryer

F1/E0

User interface has failed, you need to disconnect electrical power from the oven and replace the user interface.

Oven

F1/E1

Electronic oven control board has failed.

Oven

F2/E0

The user interface won't respond.

Oven

F2/E1

There's a defective button on the user interface.

Oven

F3/E0

The upper oven temperature sensor is defective.

Oven

F3/E1

The lower oven temperature sensor is defective.

Oven

F3/E3

The meat probe is defective.

Oven

F5/E0

The oven door switch and oven door lock switch don't agree.

Oven

F5/E1

The oven door lock assembly doesn't work.

Oven

F6/E0

There's no communication between the user interface and the electronic oven control board.

Oven

F6/E1

The oven is too hot when baking or broiling.

Oven

F6/E2

The oven is too hot when in clean mode.

Oven

F6/E4

The user interface and electronic oven control board are not matched.

Oven

F6/E5

The electronic control board was programmed incorrectly.

Oven

F1-E0 to F1-E9

There is a problem with the control board (clock) that needs to be replaced or checked.

Stove

F2-E0 to F2-E6

There is a problem with the touchpad (keypad) that needs to be replaced or checked.

Stove

F3-E0 and F3-E3

There is an issue with the oven temperature sensor (RTD) that needs to be replaced.

Stove

F4-E1

There is a defect in the meat probe that needs to be replaced.

Stove

F5-E Codes

There is a problem with the door switch that needs to be replaced or checked.

Stove

F6-E0

There is an issue with the return line that needs to be replaced.

Stove

F7-E1

There is a problem with the common switch wire that needs to be checked and fixed.

Stove

2 Digit Failure Codes (F0 to F9)

There is a control board failure or oven door lock failure that needs to be checked and replaced.

Stove/Oven

F1E4

Control board failure.

F2E0/F2E1

Touchpad not connected to control board (clock).

F2E3

Touchpad is either shorted or a key is held down for too long.

Err1

The coffee maker may display this error if it is near an outside wall in a cold climate or if the water is quite cold.

Coffee Maker

Err2

An electrical component has been dislocated within the coffee maker.

Coffee Maker

Err4

The coffee maker may have a stuck button.

Coffee Maker

1-1 or F1E1

Stuck relay on the electronic control board

Dishwasher

1-2 or F1E2

Damaged or corrupted memory on control board. Incompatible software components inside microprocessor.

Dishwasher

2-1 or F2E1

Stuck button on the user interface control

Dishwasher

2-2 or F2E2

User interface control can't communicate with electronic control board

Dishwasher

3-1 or F3E1

Thermistor/OWI sensor failure (The thermistor is the water temperature sensor, the OWI sensor is the Optical Water Indicator that detects the amount of debris in the water.)

Dishwasher

3-2 or F3E2

Shorted thermistor/OWI sensor

Dishwasher

3-3 or F3E3

OWI failed to calibrate or the drain hose check valve failed, allowing dirty water to backflow into the dishwasher

Dishwasher

5-1 or F5E1

There is a door switch failure.

Dishwasher

5-2 or F5E2

The control detects that the door is not opening.

Dishwasher

6-1 or F6E1

The dishwasher won't fill.

Dishwasher

6-2 or F6E2

There is a water inlet valve failure.

Dishwasher

6-3 or F6E3

Suds or air are in the water pump.

Dishwasher

6-4 or F6E4

The float switch is open.

Dishwasher

6-6 or F6E6

The incoming water is too cold.

Dishwasher

7-1 or F7E1

The heating element doesn't work.

Dishwasher

7-2 or F7E2

The heating element won't shut off.

Dishwasher

8-1 or F8E1

There is a slow drain.

Dishwasher

8-2 or F8E2

There is a drain pump electrical problem.

Dishwasher

9-1 or F9E1

The electronic control board can't detect the position of the diverter disc.

Dishwasher

9-2 or F9E2

The diverter motor is stuck on.

Dishwasher

9-3 or F9E3

The diverter disc is missing.

Dishwasher

9-4 or F9E4

There is a lower spray arm error.

Dishwasher

10-1 or FAE1

There is a detergent dispenser failure.

Dishwasher

10-2 or FAE2

There is a vent wax motor electrical problem.

Dishwasher

10-3 / FAE3

There is a drying fan failure.

Dishwasher

PO

Power outage. Press the Measured Fill button to confirm.

Refrigerator

Door Ajar Alarm

Alarm sounds when refrigerator door or freezer drawer is left open for 5 minutes. Close all doors to turn off.

Refrigerator

Back and 1 Cup

Press and hold Options and Lock buttons to calibrate Measured Fill feature.

Refrigerator

Locked

Dispenser controls and levers are deactivated when locked. Press and hold Lock for 3 seconds to lock the dispenser.

Refrigerator

F1

Motor Controller Module Fault - An error has occurred in the Motor Controller Module.

Washing Machine

F2

Pressure Sensor Fault - An error was encountered when trying to read the pressure sensor.

Washing Machine

F3

Motor Controller Module Fault - The Motor Controller Module has recorded a memory error.

Washing Machine

F4

Communications Fault - The Display Module has had difficulty communicating with the Motor Controller.

Washing Machine

F5

Communications Fault - The Motor Controller has had trouble communicating with the Display Module.

Washing Machine

F6

Motor Controller Module Fault - The Motor Controller Module received an incorrect signal from the pressure sensor.

Washing Machine

F6

Motor Controller Module Fault - The Motor Controller module has received an incorrect signal from the pressure sensor.

Washing Machine

F7

Display Module Fault - The Display module has found a memory fault.

Washing Machine

F8

Display Module Fault - The Display micro has not been able to start up correctly.

Washing Machine

F9

Machine Size Fault - The Display size switch setting does not match that stored in the memory.

Washing Machine

F10

Temperature Sensor Fault - The temperature sensor may be open circuit or the ambient temperature is below minus 10oC.

Washing Machine

F11

Pressure Sensor Fault - The Motor Controller micro has detected a negative pressure when trying to measure the water level.

Washing Machine

F12

Overfill Fault - The Motor Controller module has found the water level to be above the flood level and tried to pump the excess water out.

Washing Machine

F13

Pump Fault - The Display module has detected that the pump is on when it should be off.

Washing Machine

F14

Pump Connection Fault - The Display Module has detected that the pump is not on when it should be.

Washing Machine

F15

Display Module Fault - The Display Module has read an incorrect voltage on the pump circuit.

Washing Machine

F17-F23

Display/Motor Controller out of Sequence - The Display Module has read an incorrect voltage on the pump circuit.

Washing Machine

F25

Display Module Fault - The Intuitive Display has detected a problem with the LCD.

Washing Machine

F28-F30

Display/Motor Controller out of Sequence - Same as fault 17.

Washing Machine

F32

Pump Circuit Fault - The Display Module has detected that the pump is on when it is off.

Washing Machine

F33

Water Valve Fault - The Module has detected a water valve fault.

Washing Machine

F34

Brake Resistor Fault - The circuit that controls the braking of the motor is faulty.

Washing Machine

F35

Display Module Fault - The Display Module has sent a false signal to the Motor Controller.

Washing Machine

F36

Water Loss Fault - The Motor Controller module has needed to top up the water level too many times during agitation.

Washing Machine

F37

Drain Pump Fault - The water has not drained from the drum.

Washing Machine

F38

Pressure Sensor Fault - The Motor Controller module has recorded a water level of empty while agitating.

Washing Machine

F39

Temperature Tube Fault - The pressure tube has become blocked or kinked or has fallen off.

Washing Machine

F40

Bowl Dis-engage Fault - The Motor Controller module has found that the bowl is not engaged even though the pressure sensor indicates it's empty.

Washing Machine

F41

Temperature Sensor Fault - The temperature sensor is measuring temperatures above 110°C, the fault is probably due to a short circuit in the sensor line.

Washing Machine

F42

Rotor Fault - The Motor Controller has had confusing information feedback.

Washing Machine

Err2 or E2

Drain Pump Failure

All Models

Err3 or E3

NTC1 Error (Exhaust Thermistor Error)

DE7060M1, DE5060M1, DE4060M1, DE8060P2

Err4 or E4

Heater or Sensor Faulty

All Models

Err6 or E6

Lint Filters Blocked

All Models

Err9 or E9

NTC2 Error (Heater Thermistor Error)

DE7060M1, DE5060M1, DE4060M1, DE8060P2

E32

NTC2 is Out of Range

DH8060C1

E33

NTC3 is Out of Range

DH8060C1

E70

Voltage to Drum Motor is Incorrect

DH8060C1

E32

The second thermistor is out of range.

Dryer

E71

The dryer is overloaded.

Dryer

E72

There is a communication error between the motor and PCB.

Dryer

LO

The ambient temperature is too low.

Dryer

Keyloc

The keylock is activated.

Dryer

Door open

The door is not closed.

Dryer

Paus

The dryer is paused.

Dryer

Cln Lint

The lint filter is blocked or full.

Dryer

H20 full

The water tank is full.

Dryer

CLN cond

The condenser needs cleaning.

All models

F1

Ambient temperature exceeds 85C.

Oven

F2

Oven capacity temperature too high during pyrolytic cleaning cycle.

Oven

F3

Oven cavity temperature has exceeded 305C.

Oven

F4

Power module failure.

Oven

F5

Communication error between oven clock and oven power module.

Oven

F7

Oven door lock fault detected.

Oven

A1

CCS did not reset.

Oven

C1

Oven temperature exceeds 305C.

Oven

Erxx or Ex

Error message displayed or screen not operative.

Stove

E2 or EH

Indicates an overheating of the cooking zone/s.

Stove

E6

The cooker has been incorrectly connected.

Stove

F1

The flood switch has been activated. Turn off water and power supply, check for leaks, and replace sensor if none are found.

Dishwasher

F2

There is a motor problem. Check motor resistance and contact an Authorized Service Centre for assistance.

Dishwasher

F3

The temperature sensor has failed. Ensure water coming in through the inlet hose is less than 65°C, and consider installing a tempering valve on your water supply.

Dishwasher

F4

There is a faulty temperature sensor or element. Check the resistance of the sensor and element.

Dishwasher

F5

There is a lid fault. Turn off the power supply, then turn it on again. Check for obstructions and replace lid motors if necessary.

Dishwasher

F6

There is a lid fault. Turn off the power supply, then turn it on again. Check for obstructions and replace lid motors if necessary.

Dishwasher

F7

There is a lid fault. Turn off the power supply, then turn it on again. Check for obstructions and replace lid motors if necessary.

Dishwasher

F8

Electrical problem.

Dishwasher

F9

Electronics malfunction.

Dishwasher

U1

Fill Fault.

Dishwasher

U2

Loading error.

Dishwasher

U4

Drawer fault.

Dishwasher

F2

Defrost Issue

Fridge

F3, F4

Temperature Sensor Issue

Fridge

F5, F6

Freezer Compartment Sensor Issue

Fridge

F7, F8

Evaporator Sensor

Fridge

F9, F10

Refrigerator Sensor Issue

Fridge

F11, F12

Ambient Heater/PC, FC fan issue

Fridge

F13, F14

Ambient Heater Fault

Fridge

F15, F16

Refrigerator Fan Issue

Fridge

F17, F18

Freezer Fan Issue

Fridge

F20, F21

Flapper Heater Issue

Fridge

F22, F23

Water Tank Sensor Issue

Fridge

F24, F25

Ice Tray Sensor Issue

Fridge

F26, F27

Ice Maker Motor Issue

Fridge

F28, F29, 40, 41

Ice Maker Solenoid Issue

Fridge

F42, F43

Ice maker fill tube issue

Fridge

F30, F31

Display harness issue

Fridge

F49

Electronic communication error

Fridge

Err1

Door not closed - Verify the door is closing properly and the latch is closing completely. Service may be required.

Washing Machine / Washer Dryer Combo

Err2

Not draining - Verify the drain pump filter is clear and the drain hose is not kinked or crimped.

Washing Machine / Washer Dryer Combo

Err5

Unit not sensing full water fill - Check water line connections and supply valves.

Washing Machine / Washer Dryer Combo

Err7

Service is required.

Washing Machine / Washer Dryer Combo

Err8

Service is required.

Washing Machine / Washer Dryer Combo

Err9

Service is required.

Washing Machine / Washer Dryer Combo

E10

Service is required.

Washing Machine / Washer Dryer Combo

E13

Buildup of lint causing issue - Could be resolved by washing and drying a single dish towel and adding a cup of white vinegar to the drum, or making sure unit is connected to cold water properly.

Washing Machine / Washer Dryer Combo

E1

Water not drained within 4 minutes - Clear the pump or service is required.

Washing Machine / Washer Dryer Combo

E2

Door cannot be locked after 20 seconds - Service is required.

Washing Machine / Washer Dryer Combo

E4

Selected water level not reached after 8 minutes - Check plumbing and water hose connections, or service is required.

Washing Machine / Washer Dryer Combo

E8

Water level above warning level - Service is required.

Washing Machine / Washer Dryer Combo

F7

Motor circuit error - Service is required.

Washing Machine / Washer Dryer Combo

F9

Dryer sensor circuit problem - Service is required.

Washing Machine / Washer Dryer Combo

FA

Water level sensor circuit problem - Service is required.

Washing Machine / Washer Dryer Combo

FC

No feedback signal from driver unit - Service is required.

Washing Machine / Washer Dryer Combo

Fd

Dryer heating is abnormal - Service is required.

Washing Machine / Washer Dryer Combo

FE

Dryer motor is abnormal - Service is required.

Washing Machine / Washer Dryer Combo

C9

Short Circuit. The PCBs failed.

Dryer

E1

The door is not closed tightly. Shut the door tightly and restart the machine.

Dryer

E2

There is no change in the temperatures of the laundry in the tub.

Dryer

E3

The laundry is not dried.

Dryer

E4

Heating Element Problem. The humidity sensor failed. The unit will complete the current operating cycle. The unit can still operate under the Time cycles.

Dryer

E5

The temperature sensor failed.

Dryer

E5

The thermal sensor open-circuited or short circuited.

Dryer

E6

Drain pump fails.

Dryer

E7

Under/overvoltage fault, check power supply.

Dryer

E8

Overload warning, reduce the load and check power supply.

Dryer

F2

Drain pump error.

Dryer

F4

Temperature of laundry does not change or refrigerant leaks.

Dryer

F32, F33

Condenser thermal sensor open/short-circuited.

Dryer

F5

Communication failure between PCB and display.

Dryer

cln LInt

Clogged filters need to be cleaned.

Dryer

H2O FULL

Water tank is full, clean the water tank.

Dryer

Lo

Only use the dryer at ambient temperatures higher than 5°C.

Dryer

E13

The heating element is broken.

Oven

E41

The memory that stores the settings for the oven is empty.

Oven

E30

The device is not detecting a separator signal.

Oven

E31

The touch keys on the device are not working properly.

Oven

E29

The configuration file for the external display is incorrect.

Oven

E28

The memory that stores settings for the display is not working.

Oven

E24

The oven door is not locked.

Oven

E27

The oven door is locked but the slide grids signal is present.

Oven

E26

The oven door is not locked and the slide grids signal is not present.

Oven

E25

The oven door will not unlock.

Oven

E22

The meat probe has a short circuit.

Oven

E14

The device is detecting a separator signal.

Oven

E21

The meat probe has an open circuit.

Oven

E19

The memory that stores settings for the main board is not loaded or is not working.

Oven

E18

The external display board is too hot.

Oven

E17, E16

The external display board's NTC is not detecting a signal.

Oven

E15

The door signal is not correct for the situation.

Oven

E9

The device is having trouble communicating with the WIFI module when it is turned on.

Oven

E12

There is a communication error between the main and display PCBs.

Oven

E11

There is a short circuit in the temperature probe for the main oven.

Oven

E10

There is an open circuit in the temperature probe for the main oven.

Oven

E2

The cooking program selector is not connected to the display board.

Oven

E3

The function selector is not connected to the display board.

Oven

E4

The main board's NTC is not detecting a signal.

Oven

E5

The main board's NTC has a short circuit.

Oven

E6

The main board is too hot.

Oven

E7

The secondary oven temperature sensor is not detecting a signal.

Oven

E7

The secondary oven temperature sensor is not detecting a signal.

Oven

E8

The secondary oven temperature probe has a short circuit.

Oven

E1

There's an issue with the temperature sensor in the room.

Heatpump

E2

There's an issue with the heat-exchange sensor.

Heatpump

E4

There's an error with the indoor unit's EEPROM.

Heatpump

E7

There's a problem with communication in the indoor unit.

Heatpump

E9

The outdoor unit has high work-intense protection.

Heatpump

E14

The indoor unit's fan motor is not working properly.

Heatpump

F1

The outdoor unit's IPM has a protection error.

Heatpump

F2

The compressor is experiencing overcurrent.

Heatpump

F3

There's a communication problem between the IPM and the outdoor PCB.

Heatpump

F4

There's an error with the exhaust temperature sensor's overheat protection.

Heatpump

F6

The ambient temperature sensor has failed.

Heatpump

F7

There's a fault with the suction temperature sensor.

Heatpump

F11

The compressor is deviating from normal operation.

Heatpump

F19

The power voltage is either too high or too low.

Heatpump

F21

There's a fault with the defrost temperature sensor.

Heatpump

F22

The outdoor model's AC electricity has overcurrent protection.

Heatpump

F23

The compressor has single-phase overcurrent protection.

Heatpump

F25

There's a fault with the discharge temperature sensor.

Heatpump

F28

There's an error with the station detect loop.

Heatpump

F66

There's a fault with the ambient temperature sensor.

Heatpump

Err1

The door is not properly closed.

Dishwasher

Err2

The unit is not draining properly.

Dishwasher

Err5

The unit is not sensing a full water fill.

Dishwasher

E13

The dishwasher is experiencing a build-up of lint.

Dishwasher

E1

The washer cannot drain the water within 4 minutes.

Dishwasher

E2

The dishwasher cannot lock the door after 20 seconds.

Dishwasher

E4

After 8 minutes, the selected water level has not been reached.

Dishwasher

E8

The water level is above the warning level.

Dishwasher

F7

There is a motor circuit error.

Dishwasher

F9

Dryer sensor circuit problem

Dishwasher

FA

Water level sensor circuit problem

Dishwasher

FC

No feedback signal from driver unit

Dishwasher

Fd

Dryer heating is abnormal

Dishwasher

FE

Dryer motor is abnormal

Dishwasher

Unb

Unbalanced load

Dishwasher

F1-F9, Fr, Eh

There's an error with the sensor.

Refrigerator

E0

There's a communication error.

Refrigerator

E1, E2, E6, E9

There's an error with the fan.

Refrigerator

Er

There's an error with the ice maker.

Refrigerator

Ec, Ed, Fd, Rd, Hd

There's an error with the defrost.

Refrigerator

E10

Water Inlet Fault - Ensure the taps are turned on and hoses aren't kinked or blocked. If not, replace the water inlet valve.

Washing Machine

E11

Washing Phase Fill Error - Ensure tap is turned on and check hoses for kinks and blockages. Replace water inlet valve if needed.

Washing Machine

E12

Rinsing Phase Fill Error - Ensure tap is turned on and check hoses for kinks and blockages. Replace water inlet valve if needed.

Washing Machine

E13

Water Level Drop Error - Check drain hose position, check hoses for leaks. Replace pressure sensor if needed.

Washing Machine

E20

Drain Fault - Check drain hoses and filter for blockages. Replace drain pump if needed.

Washing Machine

E21

Drain Fault - Check drain hoses and filter for blockages or damage. Replace drain pump if needed.

Washing Machine

E22

Rinse Drain Error - Check drain hoses and filter for blockages. Replace drain pump if needed.

Washing Machine

E23

Drain Pump Triac Sensing Error - Check drain pump and wiring. Replace main PCB if needed.

Washing Machine

E24

Drain Pump Triac Sensing Circuit Fault - The main PCB needs to be replaced to solve this issue.

Washing Machine

E25

Wrong Input Signal to Microprocessor - Replace the PCB to solve this issue.

Washing Machine

E31

Pressure Switch Fault - Replace the pressure switch or the main PCB to solve this issue.

Washing Machine

E32

Pressure Switch Calibration Problem - Inspect wiring, hoses, inlet valve, and drain pump to solve this issue.

Washing Machine

E35

Pressure Sensor Fault - Check water inlet valve and pressure chamber, replace pressure sensor and/or main PCB if needed.

Washing Machine

E35

Pressure sensor detected high water level, check water inlet valve and pressure chamber, replace pressure sensor/main PCB if needed.

Washing Machine

E40-E45

Door lock issue, ensure door is closed properly, check wiring and lock, replace door lock or main PCB if needed.

Washing Machine

E50

Motor fault, check electrical plugs and replace motor if needed.

Washing Machine

E60

Heating fault, check temperature sensor and heating element, replace if faulty, replace PCB if both pass test.

Washing Machine

E61

Heating fault, check temperature sensor and heating element, replace if faulty, replace PCB if both pass test.

Washing Machine

E62

Overheating, check water inlet hose connection, replace temperature sensor if needed.

Washing Machine

EC1

Water inlet flow fault, replace water inlet valves, replace main PCB if needed.

Washing Machine

EF1

Drain fault, check drain pump filter and hoses for blockages.

Washing Machine

EF2

Too much foam, check drain pump and reduce detergent usage.

Washing Machine

EF4

Flow meter not detecting water flow - Check if water faucet is turned on and hoses don't have any kinks or blockages. Replace water inlet valves if necessary.

Washing Machine

EF5

Washing machine out of balance - Rearrange laundry and untangle any tangled up items in the wash basket.

Washing Machine

E64, E65

High limit thermostat tripped open too many times.

Dryer

E66

Thermal limiter tripped.

Dryer

E67

Heating sensor failure.

Dryer

E71 or E72

Outlet thermistor failure.

Dryer

E73

Inlet thermistor failure.

Dryer

E74

Drive motor relay failure.

Dryer

E91

Error with communication.

Dryer

E92

Compatibility issue between user interface control and electronic control board.

Dryer

E93

Machine configuration error.

Dryer

[code]

[description]

Dryer

E94

Cycle configuration error.

Dryer

E97

Program mismatch.

Dryer

EA1

Incoming power frequency out of limits.

Dryer

EA2

Incoming line voltage is too high.

Dryer

EA3

Incoming line voltage is too low.

Dryer

EA4

Improper wiring on the terminal block.

Dryer

EA5

Defective electronic control board.

Dryer

EF1

Blocked exhaust vent.

Dryer

EF3

Maximum dry time has expired.

Dryer

EF8

User interface control stuck key.

Dryer

F10

The oven is overheating and the relay board or display board needs to be replaced.

Oven

F11

The keyboard has been pressed for too long and it needs to be replaced.

Oven

F13

The internal checksum of the control has been corrupted and the display board needs to be replaced.

Oven

F14

The keyboard cable is not connected properly and the touch panel needs to be replaced.

Oven

F15

The controller failed its own check and the display board may need to be replaced.

Oven

F23

The oven lights control board is not connected properly and needs to be replaced.

Oven

F30

The RTD sensor probe has gone bad and needs to be replaced.

Oven

F31

The RTD sensor probe has been shorted and the display board needs to be replaced.

Oven

F31

The RTD sensor probe has been shorted and the display board needs to be replaced.

Oven

F43

The cooling fan speed is abnormally slow.

Oven

F44

The cooling fan speed is abnormally fast.

Oven

F90

The door motor mechanism has failed and the wiring needs to be checked.

Oven

C3

The cleaning function is not working because the door is not closed properly or the door lock is defective.

Oven

Demo

The demo mode is activated and needs to be deactivated.

Oven

F

The oven control has detected a fault or error condition and needs to be reset.

Oven

Efun

The fan needs to be reset.

Oven

2

Left front element Down key is defective.

Stove

3

Left front element Up key is defective.

Stove

4

Left front element On/Off key is defective.

Stove

6

Left rear element Down key is defective.

Stove

7

Left rear element Up key is defective.

Stove

8

Left rear element On/Off key is defective.

Stove

10

Right rear element Down key is defective.

Stove

11

Right rear element Up key is defective.

Stove

12

Right rear element On/Off key is defective.

Stove

14

Right front element Down key is defective.

Stove

15

Right front element Up key is defective.

Stove

16

Right front element On/Off key is defective.

Stove

21

Timer Down key is defective.

Stove

22

Timer Up key is defective.

Stove

23

Warm (Keep Warm) key is defective.

Stove

24

Lock key is defective.

Stove

25

Power (Main Power) key is defective.

Stove

30

Improper power supply (high voltage) or internal wiring failure.

Stove

31

Power Level Failure.

Stove

32

Low voltage output from the 12-volt power supply on the filter control board.

Stove

33

Improper voltage output from the filter control board.

Stove

34

Communication failure between the filter control board and the main power control board.

Stove

35

Improper power supply voltage (low voltage) or failed wiring connections.

Stove

36

Communication error between the main power control board and the filter control board.

Stove

39

Touch control board software incompatible with the filter control board after a new touch control board is installed.

Stove

40

Communication error between the main power control board and the filter control board.

Stove

51, 52, 53, 54

Temperature sensor failure on the respective burner.

Stove

E-24

The oven got too hot and had to turn off.

Microwave

E-22

The heat sensor was short circuiting.

Microwave

E-21

The heat sensor was not working properly.

Microwave

E-03

The oven did not heat up fast enough.

Microwave

E-23

The pre-heat setting was not reached in time.

Microwave

-SE-

The keys are shorting out.

Microwave

E-11

The gas sensor was not working.

Microwave

E-12

The gas sensor had an electrical problem.

Microwave

H04

Unplug the machine, clean up coffee powder around the flipper and then start the machine.

Coffee machine

U12

Press cancel button to return to standby mode, re-clamp bean box correctly and then start the machine again.

Coffee machine

CALC

Descaling cycle should be performed regularly to maintain a good coffee and the longevity of your brewer. Descaling done or not, simply press any button to cancel "CALC".

Coffee machine

Er-01

A sensor detected a water leak, turn off the dishwasher, inspect hoses and pumps, and replace leaking parts.

Dishwasher

Er-02

There's an issue with the thermistor/turbidity sensor.

Dishwasher

Er-03

The wash motor is not working.

Dishwasher

Er-04 or Er-05

There's a problem with the upper fan/vent.

Dishwasher

Er-06

The lower fan is not working.

Dishwasher

Er-07 or Er-11

The drain valve is not working.

Dishwasher

Er-08

The user interface control is not working.

Dishwasher

Er-09

There's a communication issue between the user interface control and the electronic control board.

Dishwasher

Er-10

The electronic control board relay is not working.

Dishwasher

Er-12

There's a drain valve position error.

Dishwasher

Er-13

The electronic control board is not working.

Dishwasher

Sb / 5b

The refrigerator is in Sabbath mode.

Fridge

dF

There is an issue with the defrost circuit.

Fridge

SY CE / 5Y CE

Communication with Main Control Board failed.

Fridge

SY EF / 5Y EF

There is an issue with the evaporator fan circuit.

Fridge

OPSH / 5H / 2 / 3, 0P

There is an issue with the Freezer or Fresh Food Sensor.

Fridge

E1

Water Flow - Check the setting of the cold water tap.

Washing Machine

E4

Over flow - Float switch activated

Washing Machine

E6

Open circuit heating sensor

Washing Machine

E8

Divertor Valve - open circuit or broken

Washing Machine

Err C

BLDC motor failed

Washing Machine

AF or F4E3

Restricted air flow due to lint screen/vent being clogged.

Dryer

F# E#

Dryer control detected a problem requiring service.

Dryer

L2

Low/no line voltage, possibly a problem with home power supply.

Dryer

PF

Power failure.

Dryer

LE

The appliance has activated its frost prevention system.

Heatpump

HL

The internal safety tray is full.

Heatpump

CF

The water filter needs replacing.

Heatpump

PF

The sensor is damaged and needs to be fixed.

Heatpump

F1

The water filter is clogged and needs to be changed.

Heatpump

Lo

The room temperature is too low.

Heatpump

H1

The room temperature is too high.

Heatpump

E1

The sensor is damaged and needs to be fixed.

Heatpump

FILL TANK!

The water tank is empty or positioned incorrectly.

Coffee Machine

GROUND TOO FINE ADJUST MILL!

The machine cannot make coffee as there is air in the hydraulic circuit or the grinding is too fine.

Coffee Machine

INSERT WATER SPOUT!

The water spout is not inserted or inserted incorrectly.

Coffee Machine

EMPTY GROUNDS CONTAINER!

The grounds container is too full or more than 3 days have passed since coffee was made.

Coffee Machine

INSERT GROUNDS CONTAINER!

After cleaning, the grounds container has not been replaced.

Coffee Machine

INSERT MILK CONTAINER!

The milk container is not inserted.

Coffee Machine

DESCALE!

The machine must be descaled.

Coffee Machine

ADD GROUND COFFEE!

The “pre-ground coffee’ function has been selected without preground coffee in funnel, or it is clogged.

Coffee Machine

LESS COFFEE!

Too much coffee has been used.

Coffee Machine

FILL BEANS CONTAINER!

The coffee beans have run out.

Coffee Machine

INSERT INFUSER ASSEMBLY!

The infuser has not been replaced after cleaning.

Coffee Machine

CLOSE DOOR!

The service door is open.

Coffee Machine

GENERAL ALARM!

The inside of the appliance is very dirty.

Coffee Machine

PRESS CLEAN BUTTON!

Milk has been delivered recently and the tubes in milk container must be cleaned.

Coffee Machine

E1

There's not enough water coming out.

Dishwasher

E4

Too much water caused a switch to go off.

Dishwasher

E6

The heating sensor isn't working properly.

Dishwasher

E8

The divertor valve has a problem.

Dishwasher

Err C

The motor has stopped working.

Dishwasher

LOC

Control Lock Activated - To unlock the control, press the Control Lock button or follow the instructions in the Owner's Manual (for older models) which may involve pressing and holding the button.

Washing Machine

LC

Control Lock Enabled - To disable the control lock, press the Control Lock button or refer to the Owner's Manual (for older models) which might specify holding down the button.

Washing Machine

rL

Presence of items detected in the washer during the Clean Washer cycle - Clear the drum of any items and restart the Clean Washer cycle.

Washing Machine

F34

Detection of items in the washer during the Clean Washer cycle - Remove any items in the drum and initiate the Clean Washer cycle again.

Washing Machine

Sud

Excessive suds in the washing machine - The washer will extend the rinse time to remove the suds. Use HE or High Efficiency detergent. Check if you used "no splash" or "easy pour" liquid chlorine bleach and switch to regular liquid bleach products. Ensure the drain hose is not clogged or kinked.

Washing Machine

Sd

Too many suds in the washing machine - The washer will extend the rinse time to reduce the suds. Use HE or High Efficiency detergent. Check if you used "no splash" or "easy pour" liquid chlorine bleach and switch to regular liquid bleach products. Ensure the drain hose is not clogged or kinked.

Washing Machine

F5

Incorrect door lock - Check for any obstacles blocking the door and ensure it is closing properly.

Washing Machine

E2

Problem with door locking mechanism - Make sure there are no obstructions blocking the door and confirm it is closing fully.

Washing Machine

F7

Motor Speed Detection Error - Check that shipping bolts have been removed and the washer is not overloaded.

Washing Machine

E1

Motor Speed Detection Problem - Verify that shipping bolts have been removed and the washer is not overloaded.

Washing Machine

F8

Water Flow Problem - Check that the household water supply is turned on and both the cold and hot water faucets/valves are fully open and the water inlet hoses are not kinked or clogged.

Washing Machine

E1

Water Flow Problem - Verify that the household water supply is open and the water inlet hoses are free of kinks or blockages.

Washing Machine

LO

Insufficient Water Supply - Confirm that the household water supply is on and the water inlet hoses are not crimped or obstructed.

Washing Machine

FL

Low Water Input - Ensure that the household water supply is functioning and both the cold and hot water valves are open and the water inlet hoses are not pinched or blocked.

Washing Machine

F9

Prolonged Drain Time - Verify that the drain hose is free from kinks and blockages and that you are using High Efficiency detergent.

Washing Machine

E1

Extended Drain Time - Ensure the drain hose is not obstructed or clogged and that HE detergent is being used.

Washing Machine

dET

Detergent cartridge not detected in the dispenser (on select models) - Ensure the dispenser cartridge is inserted correctly and the dispenser drawer is shut completely.

Washing Machine

Int

Cycle was paused or canceled - To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute.

Washing Machine

E2

Dispenser System Problem - Verify that the detergent drawer or detergent cartridge is not clogged with detergent.

Washing Machine

F1e1

Motor isn't working correctly on the electronic control board.

Dryer

F1e3

Wrong electronic control board installed.

Dryer

F2e1

Stuck button on control panel.

Dryer

F2e4

Problem with user interface software.

Dryer

F2e5

Problem with user interface software.

Dryer

F3e1

Exhaust thermistor isn't working.

Dryer

F3e2

Moisture sensor isn't working.

Dryer

F3e3

Inlet thermistor isn't working.

Dryer

F4e1 or F4e2

Heater relay isn't working.

Dryer

F4e3

Airflow restriction.

Dryer

F4e4

Voltage supply problem.

Dryer

F4e2 or F6e3

Communication error.

Dryer

01

Thermistor is defective.

Dryer

02

Not heating.

Dryer

03

Door switch malfunction.

Dryer

04

Drive motor relay failure on machine control board.

Dryer

08

Stuck key on control panel.

Dryer

PF

Power failure.

Dryer

F-01

Main electronic control board failure.

Dryer

F-02

User interface keypad failure.

Dryer

F-22

Exhaust thermistor failure.

Dryer

F-23

Exhaust thermistor failure.

Dryer

F-26

Drive motor failure.

Dryer

F-28

Moisture sensor failure.

Dryer

F-29

Moisture sensor failure.

Dryer

F1:-1

Upper Runaway Cook - Temperature of the upper oven is out of control.

Oven

F1:-2

Lower Runaway Cook - Temperature of the lower oven is out of control.

Oven

F1:-3

Upper Runaway Clean - Temperature of the upper oven is too high during the cleaning cycle.

Oven

F1:-4

Lower Runaway Clean - Temperature of the lower oven is too high during the cleaning cycle.

Oven

F1:-L

Oven Temperature Sensor, Track, Control - Problem with the oven temperature sensor or track.

Oven

F3:-1

Oven Temperature Sensor, Upper Oven - Problem with the upper oven's temperature sensor.

Oven

F3:-2

Oven Temperature Sensor, Lower Oven - Problem with the lower oven's temperature sensor.

Oven

F1:-5

Keypad Cancel Upper - Unexpected input from the upper oven's keypad.

Oven

F1:-5

Keypad Cancel Upper - Unexpected input from the upper oven's keypad.

Oven

F1:-6

Keypad Cancel Lower - Unexpected input from the lower oven's keypad.

Oven

F1:-7

Keypad Disconnected - Faulty connection between the oven's keypad and electrical range control (ERC).

Oven

F1:-8

Keypad Shorted - Short circuit detected in the oven's keypad.

Oven

F1:-A

Upper Latch Switch - Problem with the upper oven door's latch switch.

Oven

F1:-B

Lower Latch Switch - Problem with the lower oven door's latch switch.

Oven

F1:-C

Upper Door Switch - Problem with the upper oven door's switch.

Oven

F1:-D

Lower Door Switch - Problem with the lower oven door's switch.

Oven

F9:-1

An obstruction is preventing the upper oven door's lock from activating.

Oven

F9:-2

An obstruction is stopping the upper oven door's lock from releasing.

Oven

F9:-3

Both the upper oven door's lock and release mechanisms are blocked.

Oven

F9:-4

An obstruction is preventing the lower oven door's lock from activating.

Oven

F9:-5

An obstruction is stopping the lower oven door's lock from releasing.

Oven

F9:-6

Both the lower oven door's lock and release mechanisms are blocked.

Oven

F1:-E

Problem with the oven's Electronic Range Control (ERC).

Oven

F1:-H

Problem while retrieving information from the oven's Electronic Range Control (ERC).

Oven

F0

Function Key Stuck - Function key is stuck on the oven's keypad.

Oven

F1

Defective Touch Pad or Membrane - The oven's keypad or membrane of the keypad is defective.

Oven

F7

Replace Touch Pad or Repair ERC - Replacement or repair of the oven's keypad or Electronic Range Control (ERC) is needed.

Oven

F5

Hardware and Watchdog Circuits Disagree - The hardware and watchdog circuits of the oven are not in agreement.

Oven

F8

Analog/Digital Supervisory - Problem with the oven's analog/digital supervisory system.

Oven

AccuPop Fail

Failed AccuPop sensor

Microwave

Demo Mode (dOn/dOff)

Active or inactive Demo Mode

Microwave

Open/Close Door Error

The door is closed but not started, or an incorrectly shut door

Microwave

Loc/L/Padlock Icon

Active Control Lock

Microwave

SE/E03/F2/F2Q1/F2E1/F9Q1

Keypad or keypad wiring fault

Microwave

PF or Flashing

Power failure or turned-off clock

Microwave

Code FC (FCE – E7)

Failed router/Wi-Fi connection

Microwave

FCE8

Wrong SAID number entry

Microwave

Registration Error

Failed internet connection or wrong registration entry

Microwave

E11/E12

Gas sensor issue

Microwave

F8E5

Exhaust air-temperature sensor fault

Microwave

E13/F1E4/F7/F6E0

Control board or associated wiring fault

Microwave

E21

Thermal sensor circuit or control board fault

Microwave

E23

Failed pre-heat cycle

Microwave

E24

Overheated microwave

Microwave

E61/E62/E63

Oven sensor, circuit control board, or associated wiring fault

Microwave

F1E1/F6

Relay board or associated wiring fault

Microwave

F2H1/F2H2

Failing light switch, vent fan, or associated wiring

Microwave

Code F9

Relay board, control board, or associated wiring issue

Microwave

F4E4/F3H

Failing humidity sensor or associated wiring

Microwave

0

No error detected.

Dishwasher

F0

Controller error.

Dishwasher

F1

Motor fault.

Dishwasher

F2

Heater fault.

Dishwasher

F3

High current error.

Dishwasher

F4

Detergent fault.

Dishwasher

F5

Rinse Aid fault.

Dishwasher

F7

Turbidity Sensor fault.

Dishwasher

F8

Wash Arm fault.

Dishwasher

F9

Thermistor fault

Dishwasher

1F0

Washer Arm Sensor error

Dishwasher

1F1

Conductivity fault

Dishwasher

1F2

High Limit Thermostat fault

Dishwasher

1F3

Communication Problem

Dishwasher

1F4

Cold Water Problem

Dishwasher

1F5

Current Sensor Bad

Dishwasher

PO Error Code

Indicates that your Maytag refrigerator has had a power outage and needs to be reset.

Refrigerator